Mclennan SimStep User Manual Download Page 2 | Manualshive

Page: 2 / 32

background image

SimStep

Manual - 3400 Iss. D

7

th

June 2004

page 1

User Manual for

SimStep

Single Axis Stepper Motor Drive and Controller

Mclennan Drg. No. 3400 Issue D

Associated Documents:

MSE570 E2 Data Sheet
PM600 Manual

Software:

McTerminal

Terminal and Monitor Program

The associated documents are available from the technical documents section of our web site

www.mclennan.co.uk

SAFETY NOTICE!

Position control systems are inherently hazardous. Even a small motor, if
coupled to a leadscrew, gearbox, or any other form of mechanism that
provides a mechanical advantage, can generate considerable force and
could cause serious injury. Incorrect operation can also lead to damage to
the motor or associated machinery. It is essential that the purpose of the
various fault detection features built into the

SimStep’s

PM600 controller be

fully understood and used correctly.

Mclennan Servo Supplies Ltd.
22 Doman Road,
Yorktown Industrial Estate,
Camberley,
Surrey,
GU15 3DF
UK

Telephone: +44 (0)8707 700 700
FAX:

+44 (0)8707 700 699

Sales EMAIL:

[email protected]

Technical support EMAIL: [email protected]

The manufacturer reserves the right to update the data used in this manual in line with
product development without prior notice.

«
1
2
3
4
...
»

Summary of Contents for SimStep

































Reviews:

No comments

Related manuals for SimStep

Brand: Samson Pages: 20

Brand: Ebyte Pages: 34

Brand: XVision Pages: 28

Brand: YASKAWA Pages: 61

Brand: EA Pages: 24

Brand: BEIER-Electronic Pages: 22

Brand: Danfoss Pages: 7

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Brand: Eaton Pages: 2

Brand: K&K Pages: 6

Brand: Nedap Pages: 20

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: Saitek Pages: 15

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: Mitsubishi Pages: 16

Brand: SOMFY Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands