McIntosh D1100 Owner'S Manual Download Page 26

Page: 26 / 28

Specifications

Frequency Response

+/-0.5dB from 4Hz to 20,000Hz

+0.5/-3dB from 4Hz to 68,000Hz

Total Harmonic Distortion

0.0015% (at 2V Output)

Fixed Output level

2.0Vrms Unbalanced

4.0Vrms Balanced

Variable Output level

0 - 8.0Vrms Unbalanced

0 - 16.0Vrms Balanced

Signal To Noise Ratio (A-Weighted)

111dB

Dynamic Range

100dB

Output Impedance

100 ohms Unbalanced and Balanced

Headphone Load Impedance

20 to 600 ohms

Audio Specifications

Digital Audio Specifications

General Specifications

Power Control

12VDC, 25mA

Power Requirements

Field AC Voltage conversion of the D1100 is not pos-

sible. The D1100 is factory configured for one of the

following AC Voltages:

100 Volts, 50/60Hz at 30 watts

110 Volts, 50/60Hz at 30 watts

120 Volts, 50/60Hz at 30 watts

220 Volts, 50/60Hz at 30 watts

230 Volts, 50/60Hz at 30 watts

240 Volts, 50/60Hz at 30 watts

Standby Power, less than 0.5 watts

Note: Refer to the rear panel of the D1100 for the correct

voltage.

Overall Dimensions

Width is 17-1/2 inches (44.5cm)

Height is 6 inches (15.2cm) including feet

Depth is 19 inches (48.3cm) including the Front Panel,

Knobs and Cables

Weight

26 pounds (11.8 kg) net, 41 pounds (18.6 kg) in ship-

ping carton

Shipping Carton Dimensions

Width is 27 inches (68.6cm)

Height is 12 inches (30.5cm)

Depth is 25 inches (63.5cm)

Digital Input Signal Format

Coaxial, Optical and AES/EBU Inputs - SPDIF

(PCM)

MCT and USB Inputs - PCM, DSD

Digital Input Sample Rate

Coaxial, Optical and AES/EBU: 44.1kHz to

192kHz,

24-Bit

MCT: 44.1kHz, 16-Bit

(CD)

DSD64 (SACD)

USB: 44.1kHz to 384kHz, 32-Bit

(PCM)

DSD64, DSD128, DSD256,

DXD352.8kHz, DXD384kHz

Digital Inputs

Coaxial: 0.5V p-p/75 ohms

Optical: -15dbm to -21dbm (TOS Link)

MCT: 0.5V p-p/75 ohms

USB: USB Type B Connector

Summary of Contents for D1100





























Search results

Summary of Contents for D1100

Reviews:

Related manuals for D1100

Brands by name

Popular brands

McIntosh D1100, Owner'S Manual

Search results

Summary of Contents for D1100

Reviews:

Related manuals for D1100

Brands by name

Popular brands