McCrometer Dura Mag Quick Start Installation Manual Download Page 1

D

URA

 M

AG

This Quick Start Guide is a supplement to the Installation, 

Operation and Maintenance manual supplied with this 

meter.  It is intended to be a quick reference for the basic 

installation and reading of the Dura Mag.  

It is designed to provide installation instructions when the 

location of the sensor installation has been predetermined. 

Refer to the meter manual (30122-53 Dura Mag IOM manual)  

for information on these topis:
• 

Preparation and planning for installation

• 

Site location

• 

Software configuration

• 

Detailed information on external connections, external 

power, outputs

For information on the data logger, refer to the manual 

(30121-87 McLogger IOM), downloadable from www.

mccrometer.com).

WARNING!

Incorrect installation or removal of meters 

can result in serious injury or death.  

Read 

the instructions in this guide on the proper 

procedures carefully.

 

• 

Any person installing, inspecting, or maintaining 

a McCrometer flowmeter should have a working 

understanding of piping configurations and systems 

under pressure.

• 

Before adjusting or removing any meter, be certain 

the system has depressurized completely. 

• 

Be careful when lifting meters. Meters can cause 

serious injury if lifted incorrectly or dropped.

About This Quick Start Guide

!

Quick Start Installation Guide

30122-61 Rev. 1.4

October 4, 2021

Dura Mag

Battery Powered 

Electromagnetic Flow Meter

About This Quick Start Guide.   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .1
1. 

Flow Meter Installation  . . . . . . . . . . . . . . . .2

2. 

Remote Mount Converter Installation . . . . . . .3

3. 

Converter Wiring and Connection  . . . . . . . . .4

4. Grounding  . . . . . . . . . . . . . . . . . . . . . . . .6
5. 

Activating The Display .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .7

6. 

Converter Boot.   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .7

7. 

Converter Configuration  . . . . . . . . . . . . . . .8

8. 

Error Messages for Troubleshooting . . . . . . . .8

30122-61  Rev. 1.4 | 04OCT2021

Page 1

Summary of Contents for Dura Mag









Reviews: