background image

 

- 8 - 

3.2

 

How to adjust the handle 

 

To adjust the handle, please follow the steps below: 

1.

 

Pull up the level in Figure 1, and adjust the handle 

2.

 

Lower the handle to the best operating position 

 

NOTE:  For  the  best  operating  position,  keep  your  back  straight, 

bend only your arms. 

 

3.

 

Hold the handle against your body for the best control 

 
 

4.0

 

Power Connection 

 

This  appliance  is  just  adapted  for  alternating  current,  please  check 

whether the local voltage is matched. Do not drag the appliance with the 
power cord.   

 

This  appliance  must  use  the  power  with  grounding  protect  to  prevent  the  risk  of 
electrical shock. And the outlet box should be grounded.   
This  appliance  equipped  a  12  meters’  long  power  cord  which  has  a  1.5mm

cross 

section, try your best not to use the extra power cord, if it is really needed, please use 

the cord with cross section above 1.5mm

, and 

its  length  should  be  within 

10 meters.

 

 

The  same  extra  cable  can  not  supply  multi  appliances,  or  the  too 

huge  voltage  will  affect  the  normal  operating,  also  this  will 
damage the appliances. 

 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for FM430












Reviews: