MBM MBM 208J Operation Manual Download Page 18

Page: 18 / 24

5.13 Error indications, situations, and measures

The machine will automatically stop in the following cases

Indication

Situation

Measure

①

The Start/Stop key was pressed

without sheets of paper.

②

The Start/Stop key or the Test key
was pressed with the paper feed
table lever shifted up.

③

Sheets of paper ran out in the

middle of operation in countdown
mode.

①

Set sheets of paper.

②

Shift down the paper feed table

lever.

③

Add sheets of paper.

①

A paper feed slip occurred.

②

A paper jam occurred in folding

cassette 1 or 2

①

Clean or replace the paper
separator and the paper feed rubber
rollers. See “6 maintenance” on
page 15

②

Detach folding cassette 1 or 2, and
remove the jammed paper.

①

The paper ejection table is full of

sheets of paper.

②

A paper jam occurred in the paper

ejection unit.

③

The paper ejection photosensor is

contaminated.

①

Remove the sheets of paper in the

paper ejection unit.

②

Remove the jammed paper.

③

Clean the paper ejection
photosensor.

See “6 maintenance” on page 15

①

The safety cover is open.

②

Folding cassette 1 is not properly

set.

③

Folding cassette 2 is not properly

set.

①

Close the safety cover.

②

Reset folding cassette 1.

③

Reset folding cassette 2.

①

A paper jam occurred in folding

cassette 1 or 2.

②

The speed is low.

A paper jam occurred due to a low

speed.?

①

Detach folding cassette 1 or 2, and
remove the jammed paper.

②

Increase the speed.

Summary of Contents for MBM 208J

























Search results

Summary of Contents for MBM 208J

Reviews:

Related manuals for MBM 208J

Brands by name

Popular brands

MBM MBM 208J, Operation Manual

Search results

Summary of Contents for MBM 208J

Reviews:

Related manuals for MBM 208J

Brands by name

Popular brands