MBM 405A Page 7 Operation Manual Download

Page: 7 / 52

Memorization/deletion of fold position of non-standard fold and non-standard-size paper

5-8-1

Memorization of fold position .................................................................. 30

5-8-2

Calling up fold pattern memory ................................................................ 31

5-8-3

Deletion of entire fold pattern memory ..................................................... 32

Counter setting

5-9-1 Addition

mode

..........................................................................................

5-9-2 Subtraction

mode

......................................................................................

5-9-3 Interval

mode

............................................................................................

Speed adjustment

............................................................................................. 36

Double feed detection function

5-11-1 What is double feed detection ................................................................... 37

5-11-2 Activation of double feed detection .......................................................... 37

5-11-3 Use of double feed detection ..................................................................... 38

5-11-4 When the machine stops based on double feed detection error (E-52) ........................... 38

6. Maintenance

Service, Inspection, Expendables

6-1

Cautions for maintenance service and inspection

......................................... 39

6-2

Usual maintenance service

.............................................................................. 39

6-3

Expendable supplies

......................................................................................... 39

6-4

Removal and installation, and cleaning of folder roller

............................... 40

6-5

Cleaning of the paper feed, double feed detection, paper ejection photo sensors

................. 41

6-6 Removal and installation of paper separator, paper feed rubber roller, brake rubber

............. 42

Trouble shooting and correction

7-1

Error display

7-1-1

Error display screen .................................................................................. 43

7-1-2

List of Error Codes .................................................................................... 44

7-2

Troubleshooting

................................................................................................ 45

Relocation or Disposal

8-1

Relocation

8-1-1

Removal of the machine from its present location ................................... 47

8-1-2 Transport

...................................................................................................

8-1-3 Installation

.................................................................................................

8-2

Disposal

............................................................................................................. 47

Specifications

...................................................................................................... 48

Summary of Contents for 405A





















































Search results

Summary of Contents for 405A

Reviews:

Related manuals for 405A

Brands by name

Popular brands

MBM 405A, Operation Manual

Search results

Summary of Contents for 405A

Reviews:

Related manuals for 405A

Brands by name

Popular brands