MBM 405A Page 47 Operation Manual Download

Page: 47 / 52

Problem Possible

Cause Countermeasure Reference

The power is not
applied even when
the power switch is
turned on.

The power cable plug is not
connected to the outlet.

Insert the power cable plug
firmly into the outlet.

The circuit breaker is actuated.

Remove the cause (such as

paper jam) and press the
breaker button.

2.1 Appearance

Only about 3/4
inches of the front
edge of the paper is
folded

The brake in the folding tables 1
and 2 is locked.

Raise the brake rubber and
release the lock.

6.9 Releasing the lock

Paper jam occurs
frequently at
ejection area.

The position of paper ejection

roller is not suitable for the paper
size and fold.

Set the paper ejection roller in
the optimal position.

5.6.3 Adjustment of paper
ejection roller

Full of ejected paper.

Remove the paper.

Paper feed slippage
occurs frequently.

The paper feed roller is worn out.

Replace the paper feed roller.

The paper feed roller is stained or
dirty with ink or paper dust.

Clean the paper feed roller.

6. Maintenance, Inspection,
Expendables

Paper out of specification is used.

Use a designated paper.

The paper separator is dirty.

Clean the paper separator.

6. Maintenance, Inspection,
Expendables

Double feed
frequently occurs.

The paper separator is worn out.

Replace the paper separator.

6. Maintenance, Inspection,
Expendables

The paper separator is dirty.

Clean the paper separator.

6. Maintenance, Inspection,
Expendables

Sheets of printed paper is sticking
each other.

Reset the paper after fanning

them out sufficiently.

Paper out of specification is used.

Use a designated paper.

A paper corner is
folded.

Extremely paper is curled.

Correct the curl.

Fine adjustment is not set properly. Set

the

fine

adjustment

properly one again.

5.6.2 Fine adjustment

The folding tables 1 and 2 are not
set properly.

Set the folding tables 1 and
2 properly.

Caution !

Even paper quality is within the specifications, if it has already been folded, or is curled or

wavy due to the heat of a printing machine, copier, printer, etc., the machine may not be

able to fold it properly.

Summary of Contents for 405A





















































Search results

Summary of Contents for 405A

Reviews:

Related manuals for 405A

Brands by name

Popular brands

MBM 405A, Operation Manual

Search results

Summary of Contents for 405A

Reviews:

Related manuals for 405A

Brands by name

Popular brands