1
4280159 Rev. A 10/10
PART NUMBER (s):
0000-8F-N02B
APPLICABLE MODELS:
2007 > MAZDA CX-9
ALL MODELS
REMOTE START SYSTEM
KIT CONTENTS
Remote Start
DNA Card
Remote Start Dipole Antenna Remote Start
Control Module (QTY-1)
Transmitters (QTY-1)
Wire Harness
(QTY-1)
(QTY-2)
(QTY-1)
P/N: 0000-8F-Z01
P/N: 0000-8F-M21
P/N: 0000-8F-Z02
P/N: 0000-8F-Z10
P/N: 0000-8F-N18A
GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
®
Owner's Manual
Vehicle Remote Start System
TM
Featuring PowerCode Technology
For the Ultimate in Comfort, Convenience and Security
TM
MAZDA
GENUINE ACCESSORIES
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
30
sec.
2 sec.
5X
2 sec.
Immobilizer Interface Adhesive Primer 2- Sided Tape
Module and Harness (QTY-1)
(QTY-1)
(QTY-1)
Wire Tie
(QTY 2)
IDC Wire Tap
(QTY 2)
Hood Safety
Switch
(QTY 1)
Owners
Manual
(QTY 1)
Wallet
Card
(QTY 1)
Underhood
Sticker
(QTY 1)
Long Wire
Tie
(QTY 4)
Mini Fuses
(QTY - (1) 5 AMP)
(QTY - (7) 15 AMP)
1/4” Self
Drilling Screws
(QTY 2)
PARTS BAG CONTENTS
HOOD SAFETY SWITCH KIT CONTENTS
P/N: 0000-8F-H03
Locking
Washer
(QTY 2)
SAFETY GLASSES
ELECTRICAL TAPE
WIRE CUTTERS
PLIERS
ALCOHOL or GLASS CLEANER
#2 PHILLIPS SCREWDRIVER
POWER DRILL
9/32” DRILL BIT
FIBER STICK
10 mm SOCKET AND RATCHET
1/4” SOCKET AND DRIVE
3/8” DRIVE TORQUE WRENCH
3/8” DRIVE 10mm SOCKET
HI-TEMPERATURE SILICONE
0
IMMOBILIZER INTERFACE KIT CONTENTS
P/N: 0000-8F-H05A
1. CLEAN HANDS
2. OPEN DRIVER’S DOOR WINDOW
3. RECORD RADIO STATION PRESETS
4. SET PARKING BRAKE
5. ENSURE VEHICLE WILL START UTILIZING THE IGNITION KNOB & VALET
KEY (SMART-KEY EQUIPPED VEHICLES ONLY)
6. DISCONNECT AND ISOLATE NEGATIVE BATTERY TERMINAL
7. VEHICLE MUST BE AT ROOM TEMPERATURE
Wire Tie
(QTY-10)
NOTE: BOTH VEHICLE IGNITION KEYS ARE REQUIRED AT TIME OF
INSTALLATION. DO NOT BEGIN INSTALLATION WITHOUT BOTH
KEYS.
P/N: 0000-8F-Z12
Programming
Button
(QTY 1)
P/N: 0000-8F-Z03
VEHICLE PREPARATION
IDC Wire Tap
(QTY-8)
TOOLS REQUIRED
