background image

 

Mazda CX-7

1

 

GENUINE SATELLITE RADIO KIT 

INSTALLATION INSTRUCTIONS 

 

Thank you for purchasing a genuine Mazda accessory. 
Before removal and installation, be sure to thoroughly read these instructions. 
Please read the contents of this booklet in order to properly install and use the satellite 
radio kit. Your safety depends on it. 
Keep these instructions with your vehicle records for future reference.

 

 
 
 

 

  There are several

 

WARNING

 

and

 

CAUTION

 

sections in this booklet concerning 

safety when installing. Always read and follow them in order to prevent injuries, 
accidents, and possible damage to the vehicle.

 

 

WARNING:

   

Indicates a situation in which serious injury or death could result if the 
warning is ignored. 

 CAUTION:

   

Indicates a situation in which bodily injury or damage to the vehicle 
could result if the caution is ignored. 

  If in any doubt, please ask your Mazda dealer to install the accessory in order to 

prevent errors in installation. 

  If you have any questions about the use of the accessory, ask your Mazda dealer for 

proper advice before using it. 

  Mazda and its suppliers are not responsible for injuries, accidents, and damage to 

persons and property that arise from the failure of the dealer or installer to follow these 
instructions. 

 

To ensure safety and reliability of the work, installation, removal and disposal work 
done by an Authorized Mazda Dealership is recommended.

 

 

Be careful not to lose removed parts, and be sure that they are kept free from 
scratches, grease or other dirt.

 

 

 

 

PART NAME: 

  SATELLITE RADIO KIT 

PART NUMBER:    0000 81 M09

 

(Harness Kit H5)

 

VEHICLE:   Mazda 

CX-7 

 

 

 

 

 

 

 

 

 

 

 

1ED6P11A22600 

To the dealer 

  Please turn over these instructions to the customer after installation.

 

To the customer 

  Keep these instructions after installation. The instructions may be

 

necessary for 

installing other optional parts or removal of this accessory.

 

 

Should the vehicle or this accessory be resold, always leave these instructions 
with it for the next owner.

 

Note

 

 

 

WARNING 

Summary of Contents for 0000 81 M09

































Reviews: