background image

2

COMM. 12 Robotic Pool Cleaner

  

|

  

User Manual

   1. IMPORTANT SAFETY INSTRUCTIONS

Take the Robotic Pool Cleaner out of the pool before allowing people to enter the pool.

When examining the Robotic Pool Cleaner, disconnect the main power supply.

Ensure that children do not attempt to access Robotic Pool Cleaner while it is operating.

Keep the Robotic Pool Cleaner out of the reach of children or persons with reduced physical, 
sensory or mental capabilities, or lack of experience and knowledge, unless they have been 
given supervision or instruction.

Only an original power cable must be used, at all times. Replaced by a Robotic Pool Cleaner 
certified technician, in case of need to avoid hazard.

The unit must be connected only to a supply circuit that is protected by a ground-fault 
circuit interrupter (GFCI). This GFCI should be tested on a routine basis.
To test the GFCI, push the test button. The GFCI should interrupt power.
Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, 
the GFCI is defective. If the GFCI interrupts power to the power unit without the test button 
being pushed, a ground current may be flowing, indicating the possibility of an electric 
shock. Do not use the power unit. Disconnect the power unit and contact the manufacturer 
for assistance.

To reduce the risk of electric shock replace damaged cord immedietely. Do not use 
extension cord to connect unit to electric supply; provide a properly located outlet.

Please ensure that the following PRECAUTIONS are implemented:

Only a trained operator should operate the Robotic Pool Cleaner.

Operator should keep hands away from driving belt mechanism.

Position the Caddy and power supply at least 3.5m/12ft from pool’s edge – during 

operation.

For continued protection against possible electric shock, the power supply unit should be 

placed at least 11cm / 4’’ above ground.

READ AND FOLLOW ALL INSTRUCTIONS.

Please adhere strictly to the following WARNINGS:

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

CAUTION

CAUTION

CAUTION

CAUTION

Summary of Contents for Dolphin COMM. 12










Reviews: