16
Oven Lights
The oven lights are standard 40-watt appliance bulbs. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the Off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, and then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
PROBLEM SOLVER
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call, refer
to the warranty page in this manual and scan the code there with your mobile device, or visit http://www.maytag.com/product_help. In
Canada, visit http://www.maytag.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Maytag Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
In Canada:
Maytag Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
PROBLEM
POSSIBLE CAUSES AND/OR SOLUTIONS
Nothing will operate
Power supply cord is unplugged - Plug into a grounded outlet.
Household fuse is blown, or a circuit breaker is tripped - Replace the fuse or reset the circuit breaker.
If the problem continues, call an electrician.
The control displays an F9 or F9 E0 error code - The electrical outlet in the home may be miswired.
Contact a qualified electrician to verify the electrical supply.
Cooktop will not operate
The control knob is not set correctly - Push in knob before turning to a setting.
On ceramic glass models, the oven control lockout is set - See the “Control Lock” keypad feature in
the “Feature Guide” section.
Excessive heat around
cookware on cooktop
Cookware is not the proper size - Use cookware about the same size as the surface cooking area,
element or surface burner. Cookware should not extend more than
¹⁄₂
" (1.3 cm) outside the cooking area.
Cooktop cooking results
not what expected
Control knob set to incorrect heat level - See the “Cooktop Use” section.
Range is not level - Level the range. See the Installation Instructions.
Cooktop element cycles on
and off on High setting
Element cycling due to a temperature limiter - This is normal operation. The element may cycle on
and off to keep the cooktop from overheating.
Oven will not operate
Delay Start is set - See the “Cook Time” section.
Control Lock is on - Press and hold START for 3 seconds to unlock.
Control is in Demo Mode - See the “Electronic Oven Controls” section. Demo Mode is used for display
models in a showroom.
Electronic oven control set incorrectly - See the “Electronic Oven Controls” section.
Oven temperature too high
or too low
Oven temperature needs adjustment - See “Oven Temperature Control” in the “Electronic Oven
Controls” section.
Oven indicator lights flash
Power to range is turned on or restored - See “Control Display” in the “Electronic Oven Controls”
section. If the indicator lights keep flashing, call for service. See the “Warranty” section for contact
information.
Display shows messages
Power failure (display shows flashing time) - Press CANCEL UPPER to clear the display. On some
models, reset the clock, if needed. See “Clock” keypad feature in the “Feature Guide” section.
Error code (display shows letter followed by number) - Press CANCEL UPPER to clear the display.
See “Control Display” in the “Electronic Oven Controls” section. If it reappears, call for service. See the
“Warranty” section for contact information.
Clean cycle did not work
on all spills
Several cooking cycles between Clean cycles or spills on oven walls and doors - Run additional
Clean cycles. The affresh
®
Kitchen and Appliance Cleaner or affresh
®
Cooktop Cleaner can be used for
stubborn soils.
See the “Accessories” and “Self-Cleaning Cycle” sections for more information
.
