background image

11

Beverage Options

The following beverage containers will fit in the main
unit of your SkyBox™ personal beverage vendor.

12-ounce aluminum beverage cans
12-ounce glass beverage bottles
12-ounce plastic beer bottles
20-ounce plastic water and soda bottles

Each storage bin within the main unit is equipped to
dispense bottles or cans.

Highly Carbonated Beverages: 

Stock lower storage

bins with highly carbonated beverages and make sure
they are chilled before dispensing. To avoid overflow
spills when experimenting with new, highly carbonated
beverages, wait 10-15 seconds before opening
dispensed beverage containers, and open carefully
over the sink.

Capacity:

The top storage bin will hold 10 cans or 

5 bottles. The bottom 3 storage bins will each hold 18
cans or 9 bottles. 

Important Steps For Loading

Please follow loading instructions. Improper loading
may cause the “low-indicator light” above the beverage
buttons to illuminate prematurely.

1. Make sure the main unit is OFF and the power

cord is unplugged.

2. Open the front door to the main unit, exposing the

four storage bins.

3. When loading the beverage containers, be sure to

load with the 

TOPS TOWARD THE FRONT

(i.e. long-neck bottles with necks towards the
front).

4.

IMPORTANT -

Begin loading the left end of the

storage bin, placing one beverage container on its
side all the way to the back with the top facing
forward. If loading cans, push the first one all the
way to the back and then place one directly in
front.

5. Next, move one space to the right and place

another beverage container all the way to the back.
If stocking cans, add another directly in front. (See
illustration at bottom of page.) Continue until the
storage bin is filled. Repeat with remaining storage
bins.

6. Once the bins are filled, close the door, plug the

power cord into a grounded outlet.

7. Insert corresponding

beverage cards into the
beverage selection
buttons by carefully
pulling the bottom edge
of the buttons forward
and up and slipping in
the cards. The far left button corresponds to the
top storage bin. The next button to the right
matches the storage bin that is second from the
top, etc.

Operation

Summary of Contents for Skybox MBS1976AAB

































Reviews: