background image

3

Product Dimensions

*Range can be raised approximately 1" (2.5 cm) by adjusting the 

leveling legs.

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm) 
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood 
combination above the range, follow the range hood or 
microwave hood combination installation instructions for 
dimensional clearances above the cooktop surface.

A freestanding range may be installed next to combustible walls 
with zero clearance.

*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal 

cabinet is covered by not less than 

¹⁄₄

" (0.64 cm) flame retardant 

millboard covered with not less than No. 28 MSG sheet steel, 
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 
0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the 
cooking platform and the bottom of an uncovered wood or metal 
cabinet.

Electrical Requirements - U.S.A. Only

If codes permit and a separate ground wire is used, it is 
recommended that a qualified electrical installer determine that 
the ground path and wire gauge are in accordance with local 
codes.

Do not use an extension cord.

Be sure that the electrical connection and wire size are adequate 
and in conformance with the National Electrical Code, ANSI/
NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: 
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269.

WARNING: Improper connection of the equipment-grounding 
conductor can result in a risk of electric shock. Check with a 
qualified electrician or service technician if you are in doubt as to 
whether the appliance is properly grounded. Do not modify the 
power supply cord plug. If it will not fit the outlet, have a proper 
outlet installed by a qualified electrician.

A. 27

¹⁷⁄₃₂

" (69.9 cm) max. depth with handle

B. 46

⁷⁄₈

" (119.1 cm) overall height (max.) with leveling legs 

screwed all the way in*

C. 36" (91.4 cm) cooktop height (max.) with leveling legs screwed 

all the way in*

D. 29

⁷⁄₈

" (75.9 cm) width

E. 25" (63.5 cm) depth

F. Model/serial rating plate (located on the left side frame behind 

storage drawer panel)

A

B

C

D

E

F

A. 13" (33.0 cm) max. upper cabinet depth
B. 30" (76.2 cm) min. opening width

C. For minimum clearance to top of cooktop, see NOTE*.
D. 30

¹⁄₈

" (76.5 cm) min. opening width

E. Outlet - 8" (20.3 cm) to 22" (55.9 cm) from either cabinet,

5

¹⁄₂

" (14.0 cm) max. from floor

F.

⁷⁄₈

" (2.2 cm) min. required between cutout and cabinet door or 

hinge.

A

B

D

F

E

C

Summary of Contents for MER7662WQ - Ceramic Range













Reviews: