manualshive.com logo in svg

Maytag MDG-120PHV, Installation Manual

Share
Download
Maytag MDG-120PHV Installation Manual Download Page 43

113395 - 9

Maytag Co.

41

WARNING:

If the water in the supply line or water solenoid valve freezes, the fire suppression system

will be

 INOPERATIVE!!

The manual ball cock shutoff valve 

must be

 located outside of the dryer at a distance from the dryer where it

is easily accessible.

3. Electrical Requirements

No independent external power source or supply connection is necessary.  The 24-volt power to operate
the fire suppression system is accomplished internally in the dryer (from the dryer controls).

!

WARNING:

Electrical power 

must be

 provided to the dryer at 

ALL

 times.  If the main electrical

power supply to the dryer is disconnected, the fire suppression system is
INOPERATIVE!!

WARNING: ELECTRICAL SHOCK HAZARD

Electrical shock hazard can result in serious injury.
If the water dispensing system is activated do not attempt to operate the dryer.
If the water dispensing system is activated have the dryer inspected by a qualified
agency before operating the dryer.

Summary of Contents for MDG-120PHV















































Reviews:

No comments

Brands by name

Popular brands

Load more brands