Maytag CWG3100AAS - 24

7

3.

Use a 

¹⁵⁄₁₆

" combination wrench and an adjustable wrench to 

attach the flexible connector to the adapters. Check that 

connector is not kinked. 

4.

Gas supply pipe must be located within clearance area as 

shown in the “Cabinet Dimensions” illustration in “Location 

Requirements” section.

Complete connection

1.

Open the manual shutoff valve in the gas supply line. The 

valve is open when the handle is parallel to the gas pipe.

2.

Test all connections by brushing on an approved 

noncorrosive leak-detection solution. If bubbles appear, a 

leak is indicated. Correct any leak found.

3.

Plug into a grounded 3 prong outlet.

Install Oven

1.

Using 2 or more people, lift oven partially into cabinet cutout. 

Use the oven opening as an area to grip.
NOTE:

 Push against seal area of oven front frame when 

pushing oven into cabinet. Do not push against outside 

edges.

2.

Push oven completely into cabinet and center oven into 

cabinet cutout.

A. Gas pressure regulator
B. Use pipe-joint compound.

C. Adapter (must have ½" male 

pipe thread)

D. Flexible connector

E. Manual gas shutoff valve

F. ½" or ¾" gas pipe

G. Use pipe-joint compound.

H. Adapter

A. Gas pressure regulator
B. Gas supply line

C. Electrical disconnect

D. Serial plate

E. Manual oven valve

F. Burner rating plate

G. Manifold pressure tap

A. Closed valve
B. Open valve

A

B

C

D

E

F

G

H

A

B

C

D

E

F

G

A

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, 
fire, or electrical shock.

WARNING

WARNING

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

Summary of Contents for CWG3100AAS - 24"Gas Single Oven

















Reviews: