9
ENGLISH
•
After battery charging unplug the power adapter
(10) from the mains, remove the adapter (10)
cord plug from the socket (1).
Note:
–
Duration of each next battery charging should
take from 6 to 8 hours.
–
If the blades’ motion is slowing down and you
need to continue the unit operation, you should
charge the battery, and it will take at least
1 hour, or connect the power adapter.
–
Charge the battery at the temperature from
+5 °C to +35 °C.
–
Never leave the unit connected to the mains
unattended.
–
If you haven’t used the unit for a long time (more
than 2 months), charge the battery completely
during 12 hours before using the unit.
Lubricating oil
•
To keep the unit in a good condition, you should
lubricate the blades (5, 6) after each use of the
unit.
Attention! Use only the lubricating oil (12) sup-
plied with the unit. DO NOT USE vegetable oil,
fat, oil mixed with any solvents to lubricate the
blades. Solvents will evaporate, leaving thick
grease that may slow down the motion of the
adjustable blade (5).
Installing and removing the attachments (7, 8)
•
To install the attachment (7 or 8) insert the ledge
from one side of the attachment (7 or 8) into
the groove on the unit body (4), then press the
opposite side of the attachment (7 or 8) to fix
the other ledge.
•
To remove the attachment (7 or 8) press the out-
standing part of the attachment in the direction
from the unit body (4) and remove the attach-
ment (7 or 8).
Using the unit
•
For cordless use of the unit, charge the battery fully.
Note: For corded operation, connect the power
adapter (10) cord plug to the socket (1) and plug
the power adapter into the mains.
•
Before cutting hair, switch the unit on by setting
the «0/I» power switch (3) to the «I» position and
make sure that unit operates normally and the
blades move smoothly. If there is excess lubri-
cating oil on blades (5, 6), remove it with a dry
lint free cloth.
•
Switch the unit off by setting the «0/I» power
switch (3) to the «0» position .
•
When installing the attachments (7, 8) follow
hair length marks on the attachments (7 or 8).
•
Switch the unit on by setting the «0/I» power
switch (3) to the «I» position.
•
After finishing the unit operation switch it off by
setting the «0/I» power switch (3) to the «0» posi-
tion .
Notes:
–
Always switch the unit off during the intervals in
operation.
–
Before changing the attachment switch the unit
off, when operating the unit from the mains also
unplug the power adapter (10) from the mains.
Haircutting
•
Before cutting hair make sure that the hair is
clean and dry. The best haircutting results are
reached on dry hair, not wet.
•
Seat the person so that his/her head is at your
eye level, cover his/her shoulders with a towel
and set hair with the comb (9).
•
Always start cutting from the back of the head.
•
You can cut hair along and against the direction
of hair growth, but keep in mind that the hair cut
against the growth will be shorter than the hair
cut along the growth.
•
To leave longer hair, take hair locks between
your fingers and cut hair using the hair clipper.
•
Cut off a little amount of hair at a time, later you
can return to the already cut area again for addi-
tional cutting.
•
Set the hair with the comb (9) to reveal uneven
locks.
•
You can lift the hair locks and cut them along
the comb (9).
•
Use the scissors (13) to make haircut even
•
With time you will learn to model desired hair-
cuts by yourself.
EXAMPLE OF A HAIRCUT
Note: When installing the attachments (7, 8) follow
the hair length marks on the attachments (7 or 8).
Step one
Install the «3-6 mm» attachment (7). Switch the unit
on using the power switch (3). Hold the unit with the
blades pointed upwards. Start haircutting from the
beginning of the hair growth. Slowly move the unit
upwards. Cut the head back area at the neck bottom
and near the ears.
Step two
Switch the unit off. Install the «9-12 mm» attach-
ment (8). Switch the unit on using the power
switch (3) and continue cutting hair near the top
of the head.
Step 3 – cutting temples
Switch the unit off and install the «3-6 mm» attach-
ment (7). Cut the hair on the temples. Then install
MW_2110.indd 9
25.04.2014 17:27:28
