Maxwell MW-1085, Manual Instruction

Page: 8 / 20

8
ENGLISH
•
Do not leave children unattended to prevent
using the unit as a toy.
•
For children safety reasons do not leave
polyethylene bags, used as packaging,
unattended.
ATTENTION! Do not allow children to play with
polyethylene bags or packaging film. Danger
of suffocation!
•
Check the power cord, the power plug and
the kettle body integrity periodically.
•
Never use the kettle if the power cord or the
power plug is damaged, if the unit works
improperly or after it was dropped.
•
Do not attempt to repair the unit. Do not
disassemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and apply to any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.maxwell-products.ru.
•
Transport the unit in the original package
only.
•
Keep the unit out of reach of children and
disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES
IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at
low temperature keep it for at least three
hours at room temperature before switch-
ing on.
There may be water spots in the kettle, this
is normal, as the unit has undergone fac-
tory quality control.
–
Unpack the kettle and remove any advertis-
ing stickers that can prevent the unit opera-
tion.
–
Check the unit for damages; in case of dam-
ages do not use the unit.
–
Make sure that the unit operating voltage
corresponds to the voltage of your mains.
–
Make sure that the unit is switched off.
To do this, set the power switch (5) to the
position «
0 ».
–
To fill the kettle with water, open the kettle
lid (4).
–
Fill the kettle with water up to the maximal
mark «
MAX » (6).
–
Close the lid (4), make sure that the kettle
lid (4) is closed tightly.
–
Insert the power plug into the mains socket.
–
Set the power switch (5) to the “I” position
to switch the kettle on; the light indicator (1)
will light up.
–
Once water starts boiling, the kettle will be
switched off automatically, the light indica-
tor (1) will go out. Pour water out and repeat
the water boiling procedure 2-3 times.
ATTENTION!
To avoid burns by hot steam, do not bend over
the kettle spout (3) while it is operating.
USAGE
–
First make sure that the unit is switched off.
To do this, set the power switch (5) to the
position «0».
–
To fill the kettle with water open the lid (4).
–
Fill the kettle with water not exceeding the
maximal mark «
MAX » (6).
–
Close the lid (4) and put the filled kettle on
an even stable surface.
–
Insert the power plug into the mains socket.
–
Set the power switch (5) to the “I” position
to switch the kettle on; the light indicator (1)
will light up.
–
Once water starts boiling, the kettle will be
switched off automatically, the light indica-
tor (1) will go out.
–
After switching the kettle off, wait for
10-20 seconds, then you can switch it on
again for re-boiling.
–
If you need to switch the kettle off, set the
power switch (5) to the position «0».
–
If you accidentally switch the kettle on, but
the water level appears to be minimal, the
automatic thermal switch will be on and
the kettle will be switched off automati-
cally. In this case unplug the kettle and let it
cool down for 10-15 minutes, then fill it with
water, and switch the kettle on, the unit will
operate in normal mod
e .
CLEANING AND CARE
–
Before cleaning disconnect the unit from
the mains, pour out water and let the kettle
cool down.
IM MW-1085.indd 8 23.07.2018 17:17:14