manualshive.com logo in svg

Maxon MDS Series, Programming Manual

Share
Download
Maxon MDS Series Programming Manual Download Page 2

PROGRAMMING THE MDS SPEAKER

 

 

1.  Speakers should be programmed before installation. 

2.  Power on only the speaker you want to program and wait for its power-up chime 

before you start programming

. Speakers are “powered on” when plugged into 

a power source and/or their battery back-up switch is turned on with a charged 

battery. Note: It may take up to 40 seconds for the speaker to boot up. 

3.  If programming more than one speaker, make sure that the other speakers are 

unplugged and their battery back-up is turned OFF so that they do not interfere 

during  programming.  Repeat  this  process  for  each  speaker  as  you  program 

additional speakers.   

4.  With the speaker on, insert the USB Bluetooth Dongle into an available USB 

port  on  the  computer. 

(Speakers  must  be  turned  on  first  to  hear  a  unique 

“Connection chime”). Use only one programming dongle & computer at a time 

to prevent interference when programming.

 Speaker and PC should be within 

a  few  feet  of  each  other  so  that  the  Bluetooth  connection  can  occur. 

Programmer does not need to be running for dongle to connect to the speaker. 

PC PROGRAMMER 

1.  Install  CPS  Radio  Speaker  programming  software  onto  the  PC  that  has  the 

programming dongle.   

 

2.  Run  CPS  program  and  it  will  open  to  a  blank  page.  You  will  need  to  read  the 

speaker  or  pull  up  a  previously  saved  speaker  file  (.bin).  If  this  is your  first-time 

programming, 

“read”  the  target  speaker  first  by  following  the  next  couple  of 

instructions. 

a.  Select the COM port. If you unsure of the port number it can be found in the 

Summary of Contents for MDS Series
















Reviews:

No comments

Brands by name

Popular brands

Load more brands