HOPPER SWITCH
The vacuum is equipped with a safety
switch to prevent the machine from being
switched on when the hopper cover is
open.
0 P
N G
MAXI
VACUUM
The vacuum is designed for use on large
carpeted areas such as airport concourses,
hotel
rooms, etc.
1.
Large debris such as paper cups,
plates, etc., should be picked up before
starting the cleaning process.
2.
Plan your cleaning route to work away
from the electrical source. Move ma-
chine forward at a steady pace.
WARNING:
Do not push vacuum
over power cord while machine is run-
ning. Always lift cord over vacuum.
WARNING:
Before opening hopper
cover switch off machine and
fan rotation stops t o prevent
dust and debris from being ejected.
3.
To
keep the vacuum operating at max-
imum efficiency: Periodically switch off
the machine, shake vacuum bag to
allow the finer dirt and dust to settle
into the hopper. Open hopper cover,
lift out dust bin and empty.
CIRCUIT BREAKER
The vacuum is equipped with a circuit
breaker to protect the motor in the event
an excessive overload condition occurs.
If the breaker trips, wait
2 minutes before
resettlng. If the breaker trips immediately
after resetting, check for probable cause
such as:
A. Brush adjustment set too low.
B. Obstructions in brush
or impeller.
REGULAR MAINTENANCE
1.
Shake down bag and empty debris bin,
daily.
2.
Check power cord for damaged or fray-
ed insulation.
3.
Return brush adjustment lever t o
“store” position when machine is not
use.
4.
Every 4 to
6
months remove wheels,
clean axles, and apply a thin coating
of silicone lubricant to axles.
5. The filter bag can be washed twice be-
fore losing the filtering ability. This
should be done using a mild deter ent
in cool water and hung up to
SERVICING THE
WARNING:
Remove machine power
cord from electrical source before making
any repairs of adjustments to the machine.
I M
P E ER ASS EM B
B USH
DRIVE MOTOR IMPELLER
1.
Remove intake duct.
2.
Remove impeller housing cover.
Loosen (2) screws in impeller and
remove from motor shaft.
MOTOR
1.
Loosen idler and roll belt off motor
pulley.
2. Remove intake duct, impeller and
housing.
3.
Disconnect motor leads from terminal
4. Remove (4) bolts holding motor to
chassis.
NOTE:
When re-installing motor use a
straight
to check pulley alignment
between brush and motor pulleys.
To access impeller
and
motor.
1.
Release hopper cover latches and tilt
cover back.
2.
Remove (4) screws
main cover
to chassis.
(2) located at
corners
and (2) at front inside of rear wheels.
Lift up
RIGHT side of cover and slide
to left to remove.
BELT/ B
U
S H
1.
Loosen idler pulley and roll belt off
motor pulley.
2.
Remove
guard.
3.
Remove screw from each end of brush
shaft and remove brush assembly.
NOTE:
When installing a new belt or
motor, centerline distance between
motor shaft and brush shaft should be
set at 12
Inches.
10
A. Terminal Block
Cover
B.
Intake
Duct
Housing
F.
Belt
E.
Motor
HOUSING
SHOES
NOTE
When replacing casters
or shoes
the dimensions shown in Drawing 12 must
be made to maintain efficiency of the
vacuum.
NOTE:
Make adjustments with the ma-
chine in store position setting on a
LEVEL
surface and with the casters pointing rear-
ward.
1. The distance between surface and
bottom of rear brush housing should
be 9/16 in. Check both right and left
side of housing.
2.
When replacing shoes install a screw
at each end of shoe first. Using a
straight edge install balance of screws
keeping shoe straight.
,
. . . .
STRAIGHT
EDGE
MACHINE MUST
BE IN
STORE POSITION
\
MAKE ADJUSTMENTS
REAR SHOE
WITH CASTERS
POINTING REARWARD
SHOE
5
Summary of Contents for MX22
