Maxell SSB-4W, Instruction Manual

Page: 8 / 10

EN EN
EN-13
Connect to an External Audio Device
You can connect to your audio devices,
e.g. CD player, to enjoy purely music, via
the following conections.
R L
RCA
OPTICAL COAXIAL LINE IN
HDMI IN HDMI OUT(ARC)
COAXIAL OPTICAL
R L
RCA
OPTICAL COAXIAL LINE IN
HDMI IN
HDMI OUT
Auto-on/off function is applied in this
unit. Auto-off is to facilitate people not to
control the unit when no sound is playing
in few minutes. And when there are sounds
input, the unit will switch on automatically
after few seconds. For HDMI, Auto-on
function will work with CEC only.
Warning:
If the volume of the TV or an external
device via RCA or LINE IN is too low, the
auto-off function will be triggered and the
unit will switch to standby mode after 3
minutes.
Please turn up the volume of the input source
(not the unit, but, e.g. TV or MP3 player, etc.)
slowly, until it returns to normal mode.
To avoid the auto-off being triggered
unintentionally, pre-set the source volume
higher and adjust the unit volume to a
comfortable level.
Note:
You might hear the sound over-lapping from
both the TV and the unit while following
some of the suggestion connections. To
avoid this, turn the volume of TV down to 0
or mute it.
Connections
EN-14
Turn On/Off
Turning the System ON/OFF
Press the button on the unit or remote
control.
Note:
When turning the system on, the system will
continue in the mode was set last time.
Note:
Be sure to unplug the power cord from the
outlet when the system is not in use for an
extended period of time.
The unit will switch to standby mode when
the audio cables are disconnected or
when you turn off TV/external device after
several minutes.
Adjust Volume Level
Either,
1) Press the VOL +/- button on the remote
control; or
2) Press / button on the unit,
to increase or decrease the volume level.
If the unit is connected to the TV headphone
jack, you can control the Volume Level
using the TV remote control.
If the unit is connected to TV HDMI jack
with CEC(Customer Electronics Control)
function enabled. The sound of the unit can
be controlled by the TV remote control.
Mute Sound
Press the MUTE button on the remote
control to mute. Press this button again or
VOL+/VOL- buttons on the remote control
or
/ on the unit to resume the sound.
Bass Boost
Press BASS button on the remote control to
turn on the bass. Press this button again to
switch to level 2 or to turn it off.
Select SRS Sound
Press SRS button on the remote control to
select SRS WOW HD effect. Press this button
again to cancel the effect.
Program Smart Remote Control to
Control TV
You can store a total of up to seven of
your most frequently used TV functions in
the TV learning zone of the Smart Remote
Control. This feature enables you to use
only one remote control to operate the
unit together with your TV.
The remote control codes of a TV are stored
in the Smart Remote Control. The available
preset buttons are ON/OFF , FUNCTION
, ENTER, TV VOL+/VOL-, TV CH+/CH-.
NOTE:
During the learning process, the normal
remote control functions are disabled.
1 Place the Smart Remote Control (A)
within a 5mm-50mm distance from the
TV remote control (B), pointer to pointer
as shown above.
2 Press and hold the LEARN button for 2
seconds to activate the learning mode.
A red indicator on the Smart Remote
Control (A) at LEARN button will light up.
3 Press one of the TV learning zone buttons
on the Smart Remote Control (A), the
red indicator fl ashes.
4 Press the button on the TV remote
control (B) that is to be stored on the
Smart Remote Control (A). When the
code is received successfully, the red
indicator will quickly fl ash for 3 times, If
the code is not successfully received,
the red indicator will keep on fl ashing.
5 Repeat steps 3-4 to program more
functions onto the Smart Remote Control
(A).
6 Press the LEARN button to save the
setting and to exit the learning mode.
Red indicator will turn off immediately.
Basic Operation