MAXDATA PLATINIUM 9000-4R User Manual Download Page 10

10

MAXDATA PLATINUM Server 90004R

Electromagnetic Compatibility Notices (International)

Europe (CE Declaration of Conformity)

This product has been tested in accordance too, and complies with the Low Voltage Directive (73/23/
EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to illustrate 
its compliance. 

Japan EMC Compatibility 

This is a Class A product based on the standard of the Voluntary Control Council for Interference by 
Information Technology Equipment (VCCI).  If this equipment is used in a domestic environment, 
radio disturbance may arise.  When such trouble occurs, the user may be required to take corrective 
actions. 

ICES-003 (Canada)

Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques 
de Classe A prescrites dans la norme sur le matériel brouilleur:  “Appareils Numériques”, NMB-003 
édictée par le Ministre Canadian des Communications.

English translation of the notice above:

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus 
set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the 
Canadian Department of Communications.

BSMI (Taiwan)

The BSMI Certification number and warning is located on the product safety label which is located 
visibly on the external chassis.

Summary of Contents for PLATINIUM 9000-4R



















Reviews: