background image

 

 

 

 

 

 

 

 

 
 

www.max-power.com 18 

 

26. WARANTY FORM 
 
VERY IMPORTANT: Please complete this form and fax a COPY to Max Power with a 
copy of the installation invoice or the invoice of the yacht/boat in order for the 
warranty to come into effect. 
 
To be completed by the owner: 

 

Name of owner: 
 

Tel.: 

Address: 
 

Email: 

Postcode: Country: 
Name of skipper: 
 

Tel: 

Owner's signature: 
 

Date: 
 

 

To be completed by the installer: 

Installation details 

 

Thruster model: 

Electric/Hydraulic: 

Installation date: 

Date of launching boat: 

Model and hull number of boat: 

Builder: 
Build year: 

Pleasure or commercial boat? : 

Hull construction material: 

L.O.A: Width: 
Waterline length: 

Poids total en charge: 

Tunnel Diameter, Thickness, Material & Length:

 

If Electric, Battery Type, Size & Number:

 

 

Installation checklist: 

 

Electric : 

Before using thruster

 

During use:

 

Voltage at batteries

 

 

 

Voltage at thruster motor

 

 

 

Ampere in motor power circuit

 

 

 

 

Mechanical:

 

YES / NO 

Check if the drive coupling between the motor and drive leg is correctly tightened:

 

 

Check cable connections are sufficiently tightened:

 

 

The thruster installation has been checked and the thruster functions correctly? 

 

 

 
Important: Please consult this manual for more details  

 

Name of Installer: …………………………….    Signature:.…………………………………..     

 

PLEASE RETURN BY FAX: + 

39 039 2004299

 

TO GAIN YOUR WARRANTY COVERAGE

 

 

Serial No.: 

Summary of Contents for CT35




















Reviews: