MAX power CT35 Installation Operation & Maintenance Download Page 18

 
 

www.max-power.com 17 

4)         Warranty Terms 

 
If the material is used for anything other than for pleasure craft, the guarantee is limited to a 
six-month period. 
 
Year 1 - 

All factory testing, diagnosis, repairs and replacements are performed at no 

charge to the End User. All parts and up to two hours of labour are covered for 
repairs and replacements conducted in the field.   

 
Year 2 - 

 

 

All factory testing, diagnosis, repairs and replacements are 

performed at no charge to the End User.  This excludes any damage or faults 
occurring from normal wear and tear on the following items: engine, oil seals, relay 
contacts(If warranty is registered within the 3 month period following installation) 

 

5) Warranty 

Exclusions 

 
Damage due to modifications or installation contrary to published specifications 
Cost of hauling the boat 
Damage due to repairs performed by an unauthorized service centre 
Damage due to lack of normal maintenance services 
Damage due to water  
Parts replaced due to normal wear and tear 
Repairs performed without knowledge of manufacturer (please contact dealer to receive 
Repair Authorization Number) 
Tampering of equipment by the End User 
Cost of travel to and from the job site 
Cost of economic loss, including injury to any person, damage to property, loss of income or 
profit, communication, lodging, inconvenience 
Consequential damage due to failure, including those arising from collision with other vessels 
or objects 
 

6) Procedural 

Guidelines 

 
PLEASE VIEW THE TROUBLE SHOOTING LIST TO ASCERTAIN OR SOLVE ORIGIN OF 
PROBLEM PRIOR TO CONTACTING THE DEALER/INSTALLER 
 

1) 

Contact your dealer/installer to report the problem. 

a.  If you do not know who this is contact the nearest Max Power distributor 
b.  If you are in foreign waters please contact the nearest Max Power distributor 

2) 

Ensure you have your serial number and model number to hand (top right hand 
corner of warranty) 

3) 

Dealer/Installer will come to site to decipher the cause of the fault 

4) 

If the  cause of fault is due to a manufacturing problem the dealer will contact Max 
Power to receive Repair Authorization Number. 

5)        If the problem is due to an installation error please contact your installer. 

 

IF POSSIBLE: PLEASE TAKE PHOTOGRAPHS OF THE THRUSTER TO SHOW 

PROBLEM 

 

 

The warranty as outlined above is only applicable to MaxPower manufactured 

thrusters and optional equipment as used in marine pleasure industry.  The supplier 

holds the exclusive right to test the product and determine whether it is defective 

 
 

 

Summary of Contents for CT35




















Reviews: