background image

 

 

 

 

 

 

 

 

       

 
 

www.max-power.com 15 

23. TROUBLESHOOTING GUIDE 
 

Before contacting your nearest Max Power distributor, please check the below 
troubleshooting guide. 

 

Problem 

Check  

 

The control panel does not light 
up 

 

• 

Check the 6 wire connector behind the joystick 

• 

Check the thruster's electronic control box 6 wire 

connector 

• 

Check the circuit breaker / switch in the boat's 

main DC distribution panel  

• 

Check the control box's power fuse (8 A) 

 

 

The relay is clicking but the motor 
is not running

 

 

• 

Check the motor's power fuse 

 

• 

Check the main battery isolator 

 

• 

Check the internal relay contacts 

 

• 

Check battery conditions and connections 

 

 

 
The motor is running but the 
thruster is not working

 

 

 

• 

Check the propellers are fitted 

• 

Check the motor / drive leg assembly  

• 

Check that the tunnel is not obstructed or the 

propellors blocked  

 

 
The thruster lacks power

 

 

 

• 

Check the propellers are fitted 

• 

Check the size of the batteries  

• 

Check the batteries are sufficiently charged  

• 

Check the connections are tightened correctly  

• 

Check the power cables sections

 

(See p. 6 : Recommended cable sections) 

 

 

24. WORLDWIDE DISTRIBUTION NETWORK  

 

To locate the nearest Max Power distributor,  please consult the section 

 

"Worldwide Distribution"

 on our website: 

www.max-power.com 

 

 

 

Summary of Contents for CT35




















Reviews: