manualshive.com logo in svg

Matrox Meteor-II, Installation And Hardware Reference Manual

Share
Download
Matrox Meteor-II Installation And Hardware Reference Manual Download Page 22

22

   Chapter 2: Hardware installation

Connecting a video input to Meteor-II /Multi-Channel for PCI

Connect video sources to Matrox Meteor-II /Multi-Channel’s video input 
connector, using the optional DBHD44-TO-8BNC cable. This cable has eight 
BNC connectors and a 44-pin high-density D-Subminiature plug. The wires of 
the cable are color-coded as follows:

Connecting Matrox Meteor-II /Multi-Channel for PCI to the auxiliary power 
supply input

To use Matrox Meteor-II /Multi-Channel to power your camera:

1. Use the 4-pin power cable to connect the auxiliary power supply connector to the 

power supply in the computer.

2. Ensure that the jumper is across the appropriate Matrox Meteor-II auxiliary power 

supply selection pins, for the required voltage (5 V or 12 V). See Appendix B for 
a diagram.

3. Use the DBHD44-TO-8BNC/O cable to connect your camera’s video output and 

power supply input to the video input connector. Note that the total current drawn 
by all the cameras is limited to 1.5 A, and the circuit uses an auto-resettable fuse.

Wires

Signals

Description

RED (1)

VID1_IN1

Analog Video Input1, R

GREEN (2)

VID1_IN2

Analog Video Input2, G

BLUE (3)

VID1_IN3 

Analog Video Input3, B

BLACK (4)

SYNC_IN

SYNC input

GREY (5)

O*

External trigger input

WHITE (6)

VID2_IN1 

Analog Video Input4, R

YELLOW (7)

VID2_IN2 

Analog Video Input5, G

PURPLE (8)

VID2_IN3 

Analog Video input6, B

*OPTOTRIG- is usually connected to the ground of the trigger source. It is the shield of the gray BNC.

Summary of Contents for Meteor-II







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands