manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

Matrix SPARSH VP710 User Guide

481

Music on Hold

Music on hold (MoH) is the business practice of playing recorded music to fill the silence that would be heard by the 
party placed on hold. 

To use this feature, you should specify a SIP URI pointing to a MoH server account. 

When a call is placed on hold, the phone will send a SIP INVITE message to the MoH server account. The MoH 
server account automatically answers to the SIP INVITE messages and immediately plays audio from the source 
located (LAN, Internet) to the held party.

•

MoH server is configurable via web user interface only.

•

Contact your system administrator for the SIP URI.

Procedure

Music on hold (MoH) can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure music on hold on a per-line

basis.

Configure the way on how the IP phone

processes music on hold when placing

an active call on hold.

For more information, refer 

“Appendix 

D - Configuration Parameters”

.

Local

Web User Interface

Configure music on hold on a per-line

basis.

Navigate to:

http://<phoneIPAddress>/servlet?m=m

od_data&p=account-adv&q=load&acc

=0

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Xiaomi Redmi Note 10 JE Quick Start Manual preview
Redmi Note 10 JE
Brand: Xiaomi Pages: 10
Centrality PA168S User Manual preview
PA168S
Brand: Centrality Pages: 59
Plum X350 Sync 3.5 User Manual preview
X350 Sync 3.5
Brand: Plum Pages: 17
switel M 180 Quick Start Manual preview
M 180
Brand: switel Pages: 4
Samsung SCH U520 - Cell Phone - ALLTEL Wireless Manual Del Usuario preview
SCH U520 - Cell Phone - ALLTEL Wireless
Brand: Samsung Pages: 196
Samsung SCH U540 - Cell Phone - Verizon Wireless Manual Del Usuario preview
SCH U540 - Cell Phone - Verizon Wireless
Brand: Samsung Pages: 157
Blackberry Z10 User Manual preview
Z10
Brand: Blackberry Pages: 75
Linksys WIP330 - iPhone Wireless VoIP Phone Product Data preview
WIP330 - iPhone Wireless VoIP Phone
Brand: Linksys Pages: 4
NEC N900IG Adjustment Procedure preview
N900IG
Brand: NEC Pages: 5
Avvio 400X Manual preview
400X
Brand: Avvio Pages: 45
Avvio 200 User Manual preview
200
Brand: Avvio Pages: 24
Avvio 489 User Manual preview
489
Brand: Avvio Pages: 34
Zte ZTE-U V852 User Manual preview
ZTE-U V852
Brand: Zte Pages: 143
Avvio M355X Manual preview
M355X
Brand: Avvio Pages: 20
Avvio 790 User Manual preview
790
Brand: Avvio Pages: 19
Singtech Onyx SGT-M60 User Manual preview
Onyx SGT-M60
Brand: Singtech Pages: 21
Singtech SGT-M90 User Manual preview
SGT-M90
Brand: Singtech Pages: 22
Singtech SGT-22 User Manual preview
SGT-22
Brand: Singtech Pages: 27

Brands by name

Popular brands

Load more brands