Matrix PETROL 4-IN-1 Operating Instructions Manual Download Page 48

Page: 48 / 52

11. Fault and rectification

Fault

Possible Cause

Troubleshooting

The engine does not start - Air filter dirty

- Fuel filter clogged

- Lack of fuel supply

- Fault in the fuel line

- Starting device is defective

- Flooded engine

- Spark plug connector not plugged

- No ignition spark.

- Engine defective

- Carburetor defective

- Clean / replace air filter

- Clean or replace the fuel filter

- Carry out the refuelling.

- Check fuel line for creases or

damage

- Contact the service point.

- Remove, clean and dry the spark

plug; then pull the starter rope

several times; reinstall the spark

plug

- Check the spark plug connector for

correct fit

- Clean or replace the spark plug

- Check the ignition cable for

damage

- Contact the service point

Engine starts and stops

working

- Wrong carburetor setting (idling

speed)

- Contact the service point

Engine starts, but cutting

tool stops

- Cutting tool is blocked

- Internal error (drive shaft, gearbox)

-Defective coupling

- Switch off the engine and remove

the object

- Contact the service point

Device works

intermittently (splutters)

- Carburetor is set incorrectly

- Spark plug is sooty

- On / Off switch defective

- Contact the service centre

- Clean or replace the spark plug

- Contact the service centre

Smoke development

- Wrong fuel

- Carburetor is set incorrectly

- Use regular or premium petrol with

93 octane or higher

- Contact the service centre

Device does not work at

full power

- Machine is overloaded

- Air filter is dirty

- Carburetor is set incorrectly

- Silencer clogged

- Do not press with force while

mowing / trimming.

- Clean or replace the air filter

- Contact the service centre

- Check the exhaust

The brush cutter does

not work at full power

- Blade dull or damaged

- Material to be cut is too high

(device overload)

- Sharpen or replace cutting blade

- Cut grass gradually

The grass trimmer does

not work at full power

- Cutting line too short or damaged

- Device is overloaded because

grass is too high

- Follow or replace the cutting line

- Cut grass gradually

Summary of Contents for PETROL 4-IN-1





















































Search results

Summary of Contents for PETROL 4-IN-1

Reviews:

Brands by name

Popular brands

Matrix PETROL 4-IN-1, Operating Instructions Manual

Search results

Summary of Contents for PETROL 4-IN-1

Reviews:

Brands by name

Popular brands