Matrix MHG201 Manual For Installation, Use And Maintenance Download Page 21

Page: 21 / 24

•

To ensure the optimal life expectancy of the gas hob, please follow

the operation and maintenance guideline strictly; please do not
modify the appliance.

•

Please contact your local after-sale service for repairing and

exchanging of the components (such as gas valve, control knob) if
necessary.

•

The material of the gas hob is metal, please dispose of the gas hob

in recycling when the gas hob comes to the end-of-life.

•

The packaging materials of this appliance are recyclable, please

make good use of waste materials.

Energy Efficiency Information

Attribute

Symbol

Value

Units

Model identification

MHG201

Type of hob

Built in

Number of gas burners

Energy efficiency per gas burner

Gas burner

Aux: NA

SR: 56.27

R: 55.97

Tr: 55.55

Energy efficiency for the gas hob

Gas hob

56.16

Summary of Contents for MHG201

























Search results

Summary of Contents for MHG201

Reviews:

Related manuals for MHG201

Brands by name

Popular brands

Matrix MHG201, Manual For Installation, Use And Maintenance

Search results

Summary of Contents for MHG201

Reviews:

Related manuals for MHG201

Brands by name

Popular brands