Matrix Switch Corporation MSC-XD0816L Product Manual Download

Page: 4 / 61

MSC-XD0816L Product Manual

Table of Contents

1 Getting Started...................................................................................................................................................7

1.1 Device Connections.....................................................................................................................................7
1.2 Powering Up The Device.............................................................................................................................8
1.3 Front Panel Button Interface........................................................................................................................8

1.3.1 Audio Breakaway.................................................................................................................................8

1.4 Web Page Interface.......................................................................................................................................8

1.5 Network Planning.......................................................................................................................................10

1.5.1 Installation Example...........................................................................................................................12

1.6 Advanced Panel Configuration..................................................................................................................12

2 Web page interface...........................................................................................................................................13

2.1 Overview....................................................................................................................................................13
2.2 Routing Tab................................................................................................................................................13

2.2.1 Changing a connection.......................................................................................................................14
2.2.2 Loading a preset.................................................................................................................................14

2.3 Presets Tab..................................................................................................................................................14

2.3.1 Loading Work Matrix from a source target........................................................................................15
2.3.2 Saving Work Matrix to a target..........................................................................................................15
2.3.3 Usage scenarios..................................................................................................................................15

2.4 Labels Tab..................................................................................................................................................15
2.5 Config Tab..................................................................................................................................................16

2.5.1 System Settings..................................................................................................................................17
2.5.2 Network Settings................................................................................................................................17
2.5.3 Button Panel Settings.........................................................................................................................18

2.6 Command Tab............................................................................................................................................19

3 Mascot Control Protocol.................................................................................................................................20

3.4.1 Command Names...............................................................................................................................22

3.5 Response Format........................................................................................................................................22
3.6 Command Arguments.................................................................................................................................23
3.7 System Parameters.....................................................................................................................................24

3.7.1 System Parameter Table.....................................................................................................................25

3.8 Core Commands.........................................................................................................................................25
3.9 Configuration Commands..........................................................................................................................26
3.10 Miscellaneous Commands.......................................................................................................................27

Page 4 of 61

www.matrixswitch

corp.com

Summary of Contents for MSC-XD0816L






























































Search results

Summary of Contents for MSC-XD0816L

Reviews:

Related manuals for MSC-XD0816L

Brands by name

Popular brands

Matrix Switch Corporation MSC-XD0816L, Product Manual

Search results

Summary of Contents for MSC-XD0816L

Reviews:

Related manuals for MSC-XD0816L

Brands by name

Popular brands