background image

MUC122S 3 12/04/12

MUC122S 12V Screwdriver

2 . Be aware that this tool is always in operating condition, 

because it does not have to be plugged into an electrical outlet .

3 .  Always be sure you have firm footing .
4 .  Be sure no one is below when using the tool in high locations .
5 .  Hold the tool firmly and use both hands .
6 .  Keep hands and hair away from rotating parts .
7 .  Do not leave the tool running . Do not force tool to stay in the 

“on” position . Operate the tool only when hand-held .

8 .  Do not touch the screwdriver bit, accessory or the workpiece 

immediately after operation; they may be extremely hot and 
could burn your skin .

9 .  Some material contains chemicals which may be toxic . Take 

caution to prevent working dust inhalation and skin contact . 
Follow material supplier safety data .

WARNING: 
  MISUSE or failure to follow the safety rules stated in 

this instruction manual may cause serious personal 

injury.

OPERATING INSTRUCTION 

Installing Or Removing Battery Pack

(See Fig .1, Fig .2)
1 . Your new battery pack is not 

fully charged . You may need to 
charge it before use . 

2 .  Make sure the switch is in the 

"off" position before insertion/
removal of a battery pack .

3 .  To remove a battery pack, 

depress both tabs on either 
side of the battery and pull 
downward .

4 . To insert a battery pack, align 

the battery with the tool 
housing and push battery 
inward until click indicating 
battery is fully installed .  

Charging The Battery Pack  

(See Fig .3)

1 . Battery may not charge when 

it is above a certain preset 
temperature limit . Allow temperature of battery to cool before 
charging . 

2 . The charge process will take less than one hour . 
3 . After charging, unplug the charger from the power source and 

stow away in a safe place .

Tool Operation

1 . There are 12 torque settings on the tool . Adjust to the proper 

setting for the job .

2 . Select the torque setting for the maximum torque position 

(Useful when drilling) .

3 .  Pull the bit retainer collard towards the tool while inserting 

the bit .

4 . Ensure the bit is seated properly before actuating trigger .
5 . Forward and reverse switch is actuated by a sliding 

mechanism located above the handle .

6 .  Do not change speeds while the tool is running as it may 

cause damage to the gear box .

Replace Carbon Brush

1 .  During the lifetime of a motor, 2-3 sets of carbon brushes 

may need to be replaced .

2 .  Please ensure that the battery is removed before the 

following takes place .

  a . Use T8 size bit to loosen the side panel screws and    

   remove the panel .

  b . Take out the carbon brushes on both sides and replace  

   with new units from an Authorized Matco Distributor .

  c . Insert new carbon brushes and install cover with the same  

   screws . Tighten and check operation with charged battery  

   inserted into the tool .

Fig. 1

Fig. 2

Fig. 3

Summary of Contents for MUC122S














Reviews: