MT2466 3 06/01/09
air supply
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 PSI
at the tool while running free. Higher pressure and unclean air
will shorten tool life because of faster wear and may create a
hazardous condition.
Water in the air line will cause damage to the tool. Drain the air
tank daily. Clean the air inlet filter screen on at least a weekly
schedule. The recommended hook-up procedure can be viewed
in Figure 1.
The air inlet (Figure 2), used for connecting air supply, has standard 1/4"
NPT American Thread.
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet). Minimum hose diameter should be 3/8"
I.D. and fittings should have the same inside dimensions.
TrouBleshooTing
Changes in air supply pressure or quality may cause loss of power or
erratic action. Reduced compressor output, excessive drain on the air
line, moisture or restrictions in air pipes, or the use of improperly sized
air hoses or connections (or hoses and connections in poor condition)
may reduce air pressure.
Grit or gum deposits in the tool may cut power and may be corrected
by cleaning the air strainer and flushing out the tool with gum solvent
oil or an equal mixture of SAE 10 oil and kerosene as detailed in the
LUBRICATION section. If air supply is functioning properly and cleaning
or lubricating tool does not correct performance problems, disconnect
tool from air supply and contact the nearest MatcoTools authorized
service center.
luBricaTion & MainTenance
Lubricate the air motor daily with quality air tool oil. If no air line oiler
is used, run 1/2 ounce of air tool oil through the tool by squirting oil
into the tool's air inlet or into the nearest connection to the air inlet,
reconnecting air supply, and then running tool. Do not use more than
1/2 ounce of oil, as overfilling will reduce the performance of the tool.
WarranTy
Matco warrants its air tools for a period of 1 year to the consumer. We
will repair any MT Series air tool covered under this warranty which
proves to be defective in material or workmanship during the warranty
period. In order to have your tool repaired, return the tool to any of
the Matco Authorized Warranty Centers listed, freight prepaid. Please
include a copy of your proof of purchase and a brief description of the
problem. The tool will be inspected and if any part or parts are found to
be defective in material or workmanship, the tool will be repaired free
of charge and returned to you freight prepaid.
This warranty gives you specific rights. You may also have other rights
which vary from state to state.
The foregoing obligation is Matco’s sole liability under this or any
implied warranty and under no circumstances shall Matco be liable for
any incidental or consequential damages.
Note:
Some states do not allow the exclusion or limitation of incidental
or consequential damages so the above limitation or exclusion may
not apply to you.
MaTco air coMMand
Tool Repair SV
1330 Commerce Dr.
Stow, OH 44224
(800) 433-7098
discounT Tool repair
3433 Losee Rd. #1
North Las Vegas, NV 89030
(702) 657-6570
pneuTool parTs & serVices co., lTd
33 Haas Road
Toronto
ON M9W 3A1 Canada
(416) 748-1200
(888) 748-1201 (Toll-Free in Canada)
fig. 1
fig. 2
air inleT
ThroTTle
feaTures
• Ideal for removal of rust, paint, gaskets, adhesive residue, seam sealers and automotive coatings without heat
• Includes rubber eraser wheel for graphics and pinstripe removal
• Variable speed trigger for precise speed control
MT2466 Metal Blaster Tool
Drain Daily
Regulator
Oiler
Quick Coupler
Leader
Hose
Nipple
Do Not In stall
Quick Coupling
Here
Nipple
Filter
Air Supply
Whip Hose
adJusTaBle handle
speed regulaTor
guard
