Mastervolt WHISPER 3.5M3000 RPM User Manual Download Page 7

 
 
 
 
 
 

 

INFORMATION  

 

EN / WHISPER 3.5 / December 2009 / Copyright © 2009 Mastervolt

  

7

 

 

2 INFORMATION 

 

 

2.1 SAFETY 

 

 

2.1.1 General 

 

When correctly installed and used in normal 
circumstances this generating set fulfils EC safety 
regulations. This generating set could be part of an 
installation or could be used in a way that additional 
regulations of the EC or other authorities have to be taken 
into account.  
 

Circumstances could make it also necessary 
to take additional measures. Be aware of wet 
conditions and hazardous environments 
caused by explosive gases etc 

 

2.1.2 

Electrical safety  

 

The voltage of 230 Volt generated by this 
generating set is dangerous and if instructions 
and procedures are not strictly observed may 
result in electrical shock which will result in 
severe personal injury or loss of life. 

 

  Check all wiring at least once a year. Defects, 

such as loose connections, burned cables etc. 
must be repaired immediately.  

 

  Do not work on the electrical system if it is still 

connected to a current source. Only allow 
changes in your electrical system to be carried 
out by qualified electricians.  

 

  Connection and protection must be done in 

accordance with local standards.  

 

 Using 

event based commands

 the generator can 

start unexpectedly. When working on the 
electrical system, the 30 Amp fuse must be 
removed from the Digital Diesel Control panel 
and the battery plus cable must be removed from 
the battery. 

 

Warning signs indicate parts which could be 
live. 

 

2.1.3 

Earth insulation failures  

According to local regulations and depending on the 
application it could be necessary to take measures for 
protection against earth insulation failures.  
In the standard delivery “neutral” and “ground” are not 
connected. To make a connection between “neutral” and 
“ground” could be necessary as part of a specific 
insulation failure protection system.  
Small pleasure craft in Europe is submitted to The 
Recreational Craft Directive 94/25/EC. The guidelines of 
this directive refer to (ISO 13297).  
When the installation complies with this standard the 
“neutral” and “ground” should be connected on the 
generating set. (Refer to the electrical diagram, page 15)  
 

In all situations the transfer switches between 
shore, inverter and generator should switch 
both neutral and L1. Of course this is the case 
when using a Mastervolt Mass Systemswitch.  

 
Be aware that insulation protection systems can be 
different for different applications and even within the ship 
there could be different standards for different spaces. We 
did refer to the Recreational Craft Directive that applies to 
pleasure craft up to 24 m of length. Sometimes one has to 
comply with other standards such as the rules of 
certification societies like Lloyds Register of Shipping or 
Veritas, regulations for the protection of personal, building 
legislation, etc. It is of the greatest importance to have 
expert advice on this issue.  
 

2.1.4 Installation 

 

Whisper generating sets are not self contained and have 
to be properly installed in enclosed areas such as a 
machine room.  
 

Installation includes measures to be taken to 
outlet exhaust fumes which contain carbon 
monoxide and are extremely dangerous. 

Carbon monoxide (CO) is an invisible odourless gas. 
Inhalation produces headache, nausea or death. 
Installation includes measures for proper ventilation, safe 
electric connections, safe installation of the starting 
battery, proper fitting of the cooling system and fuel pipes 
etc. Refer to the installation manual.  
 

Summary of Contents for WHISPER 3.5M3000 RPM









































Reviews: