manualshive.com logo in svg

MasterCraft 054-1209-2, Owner'S Manual, Page: 8 / 33

Share
Download
MasterCraft 054-1209-2 Owner'S Manual Download Page 8

 

8 

 
 
 
        

WARNING:

 Only use the 

diagnostic charger to charge the 
Mastercraft 18V Ni-Cd battery. Charging 
any other batteries may damage the 
charger and possibly cause serious 
injury.

 

 
Do not store or carry battery in a manner in 
which metal objects could contact the 
exposed metal end. Do not place battery in 
aprons, pockets, drawers, etc. with loose 
nails, screws, keys etc. The battery could 
short circuit causing a fire, personal injury 
or damage to the battery. 
 
Never attempt to open the battery for any 
reason. If the housing of the battery breaks 
or cracks, immediately discontinue use 
and do not recharge. 
 
Do not charge the battery if it is wet or 
shows any evidence of corrosion. 
 
A small leakage from the battery may 
occur under extreme usage, charging or 
temperature conditions. This does not 
indicate a failure. However, if the outer 
seal is broken and this leakage gets on 
your skin, follow these steps: 
1.  Wash immediately with soap and 

water. 

2.  Neutralize with a mild acid such as 

lemon juice or vinegar. 

3.  If liquid gets into your eyes, flush 

immediately with clean water for a 
minimum of 10 minutes and seek 
medical attention. 

 
 
 

NOTE:

 The battery liquid is slightly acidic. 

 
Do not incinerate the battery. It can 
explode in a fire. 
 
Do not use an extension cord. Plug the 
charger cord directly into an electrical 
outlet. 
 
Use the charger only in a standard  
120 V AC, 60 Hz electrical outlet. 

 

Do not use the charger in wet or damp 
conditions. It is intended for indoor use 
only. Do not use the charger near sinks or  
tubs. Do not immerse the charger in water. 
 
Do not allow the cord to hang over the 
edge of a table or counter or touch hot 
surfaces. The charger should be placed 
away from sinks and hot surfaces. 
 
Do not use charger to charge any batteries 
other than the cordless drill batteries. 
Other batteries may explode. 
 
Do not operate charger if cord or plug is 
damaged. Replace damaged cord and 
plug immediately. 
 
Do not operate charger if it has received a 
sharp blow, been dropped or otherwise 
damaged in any way. Have a qualified 
technician examine the charger and repair 
it if necessary. Do not disassemble the 
charger. 
 
 
 
 
 
 
 
 

BATTERY & CHARGER SAFETY 

! 

Summary of Contents for 054-1209-2


































Reviews:

No comments