Dear Customer, thank you for purchasing a MASTER S.p.A. product. This guide contains all the information you will need concerning the use of this product. Read the instructions
carefully and keep them for further consultation. The receiver module MIR is specially designed for the control of a tubular motor with
. All other use beyond
the field defined by MASTER S.p.A. is forbidden. This, as well as the breach of the instructions given in this guide, shall release MASTER S.p.A. from any liability and shall annul the
product warranty.
mechanical limit switches
At the end of the product life cycle, dispose of the device in
compliance with local regulations. This product could
contain substances that are harmful to human health and
the environment: do not dispose of the product in domestic
waste.
Disposal
Do not use radio systems in places with strong interference (for example, near police stations, airports, banks, hospitals). It is in any
case advisable to carry out a technical inspection prior to installing any radio system in order to identify possible sources of
interference. Radio systems can be used where any disturbances or malfunction of the transmitter or receiver do not constitute a
risk factor, or if such factor is eliminated using appropriate safety systems. The presence of radio devices working at the same
transmission frequency (433.42 MHz) may interfere with the radio receiver and reduce the range of the system, limiting
functionality.
Notes on radio systems
01. WARNINGS
Incorrect installation can cause serious injuries
Keep these instructions for future maintenance work and disposal of the product
All the product installation, connection, programming
and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions given on this
manual
The electrical wiring must comply with current IEC standards
Some applications require «hold-to-run» operations and can exclude the use of radio controls or require
particular safety devices
To prevent potentially dangerous situations, check the operating condition of the roller shutter/awning regularly
●
●
●
●
●
01.1 Warnings for safety
Check that the package is intact and has not suffered damages in transit
A heavy knock and the use of unsuitable tools can cause damage
Do not pierce or tamper with the box in any
way. Do not modify or replace parts without the manufacturer’s permission
The antenna cable carries line voltage. Do not cut the antenna cable as this would be dangerous. If the
antenna cable is damaged, replace the product
If there are several radio appliances in the same system, they must not be less than 1,5 m apart
The product is designed to be inserted
inside of junction boxes. The module does not provide any protection against water and only essential protection for contact with solids
It is forbidden to install the module in areas not
adequately protected, near sources of heat and near metal surface
For your safety, do not work near the winding roller while the motor is powered
●
●
●
●
●
●
●
The product is not intended for use of persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised
or given instructions on how to use the product by a person responsible for their safety
Before operating on the roller shutter/awning, make sure there are no people or objects in the area
involved in its movement. Check the automation during the movement and keep people at a safe distance, until the movement ends
Do not allow children to play with the appliance or
with the fixed control devices. Furthermore, keep the portable control devices (remote controls) out of reach of children
Do not operate on the roller shutter/awning when maintenance
operations are being carried out (e.g. window cleaning). If the control device is automatic, disconnect the motor from the power line
●
●
●
01.2 Warnings for installation
01.3 Warnings for use
Power supply:
120 o 230 Vac, 50/60 Hz
Contact capacity:
7A @ 250 Vac
Dimension:
45 x 38 x 25 mm
Weight:
40 gr
Working temperature:
–20°C / +55°C
Working time:
120 s
Frequency:
433.42 Mhz
Memorizable radio code:
15 (rain sensor included)
Memorizable wind sensor:
4
Memorizable sun sensor:
1
Range (estimated):
100m outdoor, 20m indoor
Technical specifications
Make connections with power supply disconnected
Check that the power supply does not depend from electrical circuits for lighting
The supply line must be equipped with a circuit
breaker. The installer must fit an isolation device (with 3,5 mm minimum opening on the contacts) upstream of the system
The section of the connecting cables must be proportionate
to their length and to the absorption of the load, and in any case not less than 1,5 mm
You cannot connect more than one motor directly to the module. If it is necessary to connect more
than one motor to the module use the appropriate expansion cards
●
●
●
●
02. ELECTRICAL CONNECTIONS
The module can be powered at 120 Vac or 230 Vac. The supply voltage must be
applied to terminals (
) and (
)
1 phase
2 neutral .
02.1 Power supply
The motor windings must be connected to the terminals
and , the common wire
of the motor must be connected to terminal .
4
5
3 You can not connect more than
one motor directly to the module.
If it is necessary to connect more than one
motor to the module use the appropriate expansion cards.
02.2 Connecting the motor
03. FIRST INSTALLATION
01. Give power supply to the device. The motor performs one short movement.
02. Within 15 seconds:
If the movement is upward, press UP of transmitter.
If the movement is downward, press DOWN of transmitter.
03. The motor makes a brief upward movement.
1xUP
UP
1xDOWN
DOWN
or
MIR MAXI
radio receiver for mechanical motors
R
433,42 MHz
rev00.1_26/06/2017
04. MEMORIZATION/DELETION OF A RADIO DEVICE
01. Bring the motor in an intermediate position.
02. Press PROG of an already memorized transmitter for 5 s. The motor performs 2 upward movements.
03. Within 15 seconds, to memorize/delete:
a transmitter: press STOP of transmitter you want memorize/delete
a sensor: press «1» of sensor you want memorize/delete
a rain sensor: press «2» of rain sensor you want memorize/delete
04. 1 upward movement: device memorized!!
1 downward movement: device deleted!!
2 downward movement: error!!
PROG
(5 seconds)
NOTES: point 03. in battery powered sensors may be necessary to keep the button pressed up to 10 seconds.
point 04. is reported "error" if the radio code is not received in time, if the receiver's memory is full, if you try to delete the only memorized transmitter, if you try to
memorize more than 1 sun sensor or more than 4 wind sensor
P1
P2
P1
STOP
common
L N
L
N
C
M
MAX 7A
230V
~
120-230V
50-60Hz
1
2
3
4
5
M
I
R
MAXI
