All products and technical specifications given in this document are subject to variation without notice. The manufacturer shall not be liable for damage resulting from improper, incorrect or
unreasonable use.
05. SUN, WIND, RAIN SENSOR
The sensors generate automatic manoeuvres without notice that can be dangerous. The installer must to inform the end-user and possibly integrate the installation with adequate security
systems. In some situations (eg power loss of motor or sensor, motor failure or sensor, radio noise ...) it is possible that the command imparted by the sensor is not detected by the motor.
The sensor must therefore not be understood as a safety device which ensures the integrity of the roller in every condition, but a means to reduce the possibility that the shutter being
damaged by adverse weather conditions.
05.1 COMPATIBLE SENSORS
Use sensors series BLAST or BLAST BT or SHAKE (wind sensor), VEGA and VEGA BT (sun / wind sensor), THANK YOU (sun sensor), X11 (rain sensor) associated at module
AT12.When the sensor detects the presence of wind, the "wind alarm" command is sent: the tuned motors move upward and manual controls are disabled until the end of the alarm.
When the sensor detects the presence of the sun, the "presence of sun" command is sent: the tuned motors move downward. When the sensor detects the absence of the sun, the
"absence of sun" command is sent: the tuned motors move upward. When the sensor detects the presence of rain, the "presence of rain" command is sent: the tuned motors move up or
down, depending on the settings of rain sensor. Each device can store up to 4 sensors wind, only one sun sensor. For more information, consult the manual of sensors.
As soon as the module stores a wind sensor, a communication control is automatically activated between the sensor and the device. If the communication is lost for more than 60
minutes, the motor performs an upward movement to protect the blind. This automatic manoeuvre is performed every 60 minutes until the reactivation of the radio communication. The
factory recommends to keep the “test radio” active in order to identify in good time any malfunction of the radio sensor or of the radio communication. To modify this function:
05.2 TEST RADIO
05.3 HOW TO ACTIVATE/DEACTIVATE THE «SUN FUNCTION»
(*) The motor signals the change with a quick movement up / down. For more information, consult the transmitter manual at section "sun / automatic lowering" function
ARCO
FLUTE, KUADRO, KORT
VISIO
Others transmitters..
01. Press SUN for about 2 seconds. (*)
01. Press togheter STOP/UP for about 2s. (*)
01. Press togheter STOP/UP for about 2s. (*)
(*)
06. RESET
WARNING: This procedure restores the factory settings of the device. This procedure must be carried out by qualified technical personnel. Once the "reset" is performed,
the technician must install this device again (following the procedure on section 03. FIRST INSTALLATION) and verify proper operation.
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 7 times NEXT.
«17» appears on display
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press PREV
To activate: press NEXT
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 1 time UP / 7 times DOWN.
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 7 times NEXT.
«17» appears on display
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 17 -
Test radio»
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters
01. Bring the motor in an intermediate position.
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes, the motor
performs some movement
05. Press together PREV and NEXT for about
2 seconds until the motor indicates that the
reset was performed (1 moving up / down).
06. Reinstall the motor (see section 6).
01. Bring the motor in an intermediate position.
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 2 time UP / 9 times DOWN.
04. Press STOP. The LEDs flash, the motor
performs some movement
05. Press together UP and DOWN for about 2
seconds until the motor indicates that the
reset was performed (1 moving up / down).
06. Reinstall the motor (see section 6).
01. Bring the motor in an intermediate position.
02. Press MENU, «Menu rx» appears on
display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes, the
motor performs some movement
05. Press together PREV and NEXT for about
2 seconds until the motor indicates that the
reset was performed (1 moving up / down).
06. Reinstall the motor (see section 6).
See the User manual of
the transmitter at
section:
«RECEIVER MENU
Function 29
Receiver reset»
Before perform "reset" from the transmitter:
ü
On the transmitter select the radio channel which controls the device to be reset.
ü
Make sure that this radio channel controls only the device to be reset.
WARNING: this device can be reset to factory conditions only using a transmitter already in memory. If no stored transmitter is available, use the emergency procedure
described in section 06.1 to enter a new transmitter in the memory and, if necessary, to restore factory conditions.
06.1 EMERGENCY PROCEDURE! STORING A TRANSMITTER WITHOUT USING AN ALREADY STORED TRANSMITTER
CAUTION: This procedure involves the temporary change of the electrical system. Contact authorized personnel.
Use this emergency procedure only if all the transmitters stored in the module are no longer able to operate. In all other cases, to store other transmitters in the motor using
the procedure described in section 04 "Storing / deleting a radio device".
01. Remove main power from electrical system
02. Disconnect the
from the electrical system and connect it to a plug or (if available) to the MASTER "Test Cable"
MODULE
03. Powers the electrical system (except the
)
MODULE
04. Wait at least 20 seconds
05. Give power to the
MODULE
06. Within 15 seconds, press STOP for 1 second of the
, then press PROG for 1 second of the
REMOTE CONTROL
REMOTE CONTROL
07. Remove power to the
MODULE
08. Wait a few seconds
09. Give power to the
MODULE
10. Within 15 seconds, press STOP for 1 second of the
, then press PROG for 1 second of the
REMOTE CONTROL
REMOTE CONTROL
11. Remove power to the
MODULE
12. Wait a few seconds
13. Give power to the
MODULE
14. Within 15 seconds, press STOP for 1 second of the
, then press PROG for 1 second of the
REMOTE CONTROL
REMOTE CONTROL
15. If the procedure was successful, only the motor connected to the
performs 2 short upward movements (otherwise repeat the entire procedure from step 1)
MODULE
16. Within 15 seconds, press STOP of the
. The motor connected to
performs 1 short upward movement. The
is stored !!
REMOTE CONTROL
MODULE
REMOTE CONTROL
17. Remove main power from electrical system
18. Restore the wiring
In the following procedure with "
" is indicated the MIR MAXI in which you want to store a new remote control and with "
" the new remote control to store.
Use a REMOTE CONTROL not stored in any other module.
MODULE
REMOTE CONTROL
