background image

 

14

6. 

Compressor will not start – hums, but cycles on overload 

 

A. Low 

voltage. 

B. Relay 

defective. 

C. Overload 

defective. 

D. 

High head pressure (see 1). 

 
7. 

Special service situations 

 

If moisture or liquid is observed around or under a Master-Bilt cabinet, an immediate investigation 
should be made by qualified personnel to determine the source of moisture or liquid.  The investigation 
made should determine if the cabinet is malfunctioning or if there is a simple housekeeping problem. 
 
Moisture or liquid around or under a cabinet is a potential slip/fall hazard for persons walking by or 
working in the general area of the cabinet. 
 
Any cabinet malfunction or housekeeping problem that creates a slip/fall hazard around or under a 
cabinet should be corrected immediately. 
 
 

MASTER-BILT PART NUMBERS 

 
The table below gives Master-Bilt part numbers.  Use this chart when ordering replacement parts for your 

CM/CM 

cases. 

Description CM/CL-156 

Qty 

R35E-070UU 

SK#3 & 3A 

R35XZ070UU 

SK # 1 

C12X-070UU 

SK # 1 

W46X-070UU 

28X63-RH-NSF-1092-DGT-SK#2-2P- 

D28RX070UU 

F35E-07-UU 1 

F35S-070UU 

TOTALS  

12 

 

 

Vapor Proof Light Globe(for door panel) 

23-00594 

1 " Dia. Gray Plug Buttons 

29-01287 

70 

1 " Dia. Chrome Plug Buttons 

29-01300 

5/16" Hex Cam Wrench 

35-0180 

 

 
SALE AND DISPOSAL 

 

OWNER RESPONSIBILITY

 

 
If you sell or give away your Master-Bilt cabinet you must make sure that all safety labels and the Installation- 
Service Manual are included with it.  If you need replacement labels or manuals, Master-Bilt will provide them 
free.  Contact the customer service department at Master-Bilt at (800) 684-8988. 
 
The customer service department at Master-Bilt should be contacted at the time of sale or disposal of your 
cabinet so records may be kept of its new location. 
 
If you sell or give away your Master-Bilt cabinet and you evacuate the refrigerant charge before shipment, 
Master-Bilt recommends that the refrigerant charge be properly recovered

 in compliance with section 

608 

of the Clean Air Act effective November 1995 and in accordance with all applicable local, regional, or national 
standards.

 

Summary of Contents for CL-156





















Reviews: