background image

1. Introduction 

The Tester is a handheld and battery operated very convenient small   

Tool that is specially used to measuring SMD 

Surface Mounting 

Device),  there  are  Chip  type  resistor,  Chip  type  capacitor  and  diode,  for 

example. 

Moreover, the Tester have the continuity checking function 

The Tester is automatically identified the passive 

Component as has been indicated above. Therefore, 

the measurement are allowed by fully automatic detection. 

The Tester is designed to meet IEC1010-1 standard and 

Stipulation of 2-Poulation Grade. 

The Tester conform to the European Union’s following 

Requirement:    CE regulation    89/336 (EMC Electromagnetic   

Compatibility

 

The entire outer surface of the Tester case has been with 

thermo plastic elastomer, and the two testing pins has been gold-plated, so that 

it is reduce pin contact resistance and prevent to get rusty. 

This operating instruction covers information on safety and caution, 

so  please  read  relevant  information  carefully  and  observe  all  the  warming  and 

note strictly.   

 

 

 

 
 

2.

 

Safety Note 

The following safety notes should be observed prior to using 

This Tester and any associated accessory. Although the Tester do not used to 

measuring  DC/AC  Voltage  or  Current,  but  there  are  situations  where 

hazardous condition may be present.

 

  Inspect the Tester case before using. Do not use damaged device.   

  Inspect the Pin Holder and Pin gold-plated state.   

  Do not attempt use the Tester as tweezers to prevent the pin tip 

      from damage. 

  Do not apply external voltage between the two pins.   

  Do not used in the environment with explosive gas, vapor, or dust. 

 

  Caution 

Never use the Tester on alive circuits. 

 

       
 
 
 
 
                                 

 

Summary of Contents for MS8910







Reviews: