Marvin Sliding Door Automatic Control Device Installation Instructions Manual Download Page 15

Page: 15 / 18

2022-09-08

Sliding Door Automatic Control Device

19916437

Installation Instructions

Installing the Optional Closing Ramp

Using a smartphone or similar device,
scan the QR code or click

here

to play a

video of this procedure.

NOTE: the closing ramp is mounted to the frame, and
helps apply force to the back side of the panel to ensure
the panel fully seats into the jamb. It is typically needed
on narrow and tall panels.

Fully close the door.

Locate the pre-drilled hole 1" behind the interlocking

stile.

See Figure 36

Figure 36

Open the primary panel(s) past 1 full panel width.

NOTE: If you have an OX, XO, or OX-XO unit, leave
the panel(s) fully closed.

Install the closing ramp, using the provided #8 x 3"

screw, into the pre-drilled hole.

Close and lock the door.

Pull the ramp tight so that if fully contacts the

turnbuckle.

See Figure 37

Figure 37

NOTE: If more contact is needed, adjust the set screw
in the closing ramp.

Open and close the door using Sliding Door

Automatic Control System. Ensure the door manually
locks. If the door doesn’t manually lock, adjust the set
screw.

See Figure 38

Figure 38

Summary of Contents for Sliding Door Automatic Control Device



















Search results

Summary of Contents for Sliding Door Automatic Control Device

Reviews:

Related manuals for Sliding Door Automatic Control Device

Brands by name

Popular brands

Marvin Sliding Door Automatic Control Device, Installation Instructions Manual

Search results

Summary of Contents for Sliding Door Automatic Control Device

Reviews:

Related manuals for Sliding Door Automatic Control Device

Brands by name

Popular brands