background image

 

RUSH® CS Series User Manual 

GRAZE fixtures 

The CS Series Graze fixtures fall into the following risk groups according to EN62471 at 
the distances indicated below. Position the CS Series Graze fixtures so that prolonged 
staring into the light output at less than 2.4 m (7.9 ft.) from the fixture is not expected. 

RI

S

K GROUP

2

RI

S

K GROUP

1

2.4 m

(7.9 ft.)

23.5 m

(77.1 ft.)

RI

S

K GROUP

EXEMPT

 

 

 

Protection from injury 

Fasten the fixture securely to a fixed surface or structure when in use. The fixture is not 
portable when installed. 

Ensure that all supporting structures, surfaces, fasteners and lifting equipment can bear 
the weight of all the devices they are intended to support plus an adequate safety margin, 
and that they conform to local building and safety regulations. 

Ensure that any accessory such as a glare shield is securely fastened. 

Block access below the work area and work from a stable platform whenever installing, 
setting, adjusting, or cleaning the fixture. 

Do not operate the fixture with missing or damaged covers, shields or any optical 
component. 

If an operating problem occurs, stop using the fixture immediately and disconnect it from 
power. Do not attempt to use a fixture that is obviously damaged. 

 

Summary of Contents for RUSH CS Series





























Reviews: