42
MAC 2000 Wash
D
IS46"Y
!.SS"5.S
!essage
"ppears when...
'hat to do
#%'
ZReset[
... the fixture is indexing effects at
startup.
Wait for reset to complete.
%#%'
ZSerial reset[
... the fixture has received a reset
command from the controller.
Wait for reset to complete. Set
$&#%
→
"#&%
to
1//
to prevent
accidental reset commands.
:12&
... the effects have been indexed and are
moving to their default positions.
Wait a few moments.
1$&0;
...the lamp access cover is not fully
closed.
Verify that the lamp access cover is
locked in place.
3&##
ZLamp error[
... the lamp does not ignite within -0
minutes of receiving a hLamp ONi
command. Probable causes are lamp
missing7defective, or insufficient AC
voltage.
Check the lamp. Check that the
voltage and fre_uency settings match
the local supply.
2&##
ZMemory error[
...the EEPROM memory cannot be read.
Contact Martin service personnel for
assistance.
%L&#
ZShort error[
... the fixture detects the lamp is on but
no hLamp ONi command has been
received. This can occur if the lamp relay
is stuck or if the lamp-power feedback
circuit fails. The fixture may be operated
but remote lamp on7off may be affected.
Contact Martin service personnel for
assistance.
)'&#
ZBase temperature error[
:'&#
ZHead temperature error[
... there is a fault with the temperature
sensor in the base or head.
Contact Martin service personnel for
assistance.
/)&$
ZFeedback error pan[
/)&'
ZFeedback error tilt[
/)&#
ZFeedback error pan u tilt[
...pan, tilt, or both pan and tilt feedback
circuits are malfunctioning. It is still
possible to operate the fixture, although it
switches to nsafeo mode with reduced
maximum speed, thus preventing the
fixture from losing track of its home
position Zlosing step[.
Contact Martin service personnel for
assistance.
$!&#
ZPan time-out[
'.&#
ZTilt time-out[
6C&#
ZCyan time-out[
2!&#
ZMagenta time-out[
C&&#
ZYellow time-out[
6'&#
ZCTC time-out[
6,&#
ZColor wheel -[
67&#
ZColor wheel 27dimmer
wheel time-out[
B1&#
Zqoom time-out[
...the electric indexing circuit is
malfunctioning. The fixture will, after the
time-out, establish a mechanical stop,
and continue to work normally.
Reset fixture. Contact Martin service
personnel if problem continues.
#@&#
...the barndoor rotation mechanism is
malfunctioning.
Reset fixture. Contact Martin service
personnel if problem continues.
%G%6
ZColor wheel - sensor[
%J%6
ZColor wheel 2 sensor[
%E%6
ZBarn dr. rotation sensor[
%-%6
ZBarn dr. presence sensor[
%M%6
ZYellow7CTC sensor[
%(%6
ZCyan7magenta sensor[
%N%6
Zqoom sensor[
...an effect does not move away from the
index position under reset, a sensor or
micro-switch circuit is short-circuited, or
a micro-switch is stuck or connected
incorrectly.
Contact Martin service personnel for
assistance.
#!2&
...there is an onboard RAM memory
error.
Contact Martin service personnel for
assistance.
1$&#
...there is an onboard programming error.
Contact Martin service personnel for
assistance.
3'&#
...there is a lamp temperature error.
Set fan speed to
/533
using the
5'.3
menu and restart the fixture.
Contact Martin service personnel if
problem persists.
Table 2: Display messages
Summary of Contents for MAC 2000 Profile II
