manualshive.com logo in svg

Martin Audio Wavefront W8CT, Application Manual

Share
Download
Martin Audio Wavefront W8CT Application Manual Download Page 223

Wavefront W8S Hybrid™ Subwoofer

A2.1 Introduction

The Martin Audio Wavefront W8S Hybrid™ Subwoofer combines a horn-loaded 15"
driver with a ported 18" high-excursion direct radiator. This powerful combination
gives the W8S the characteristic punch of a horn-loaded system with the low
frequency bass extension of a reflex enclosure.

The W8S is a light weight system in a trapezoidal cabinet. It has the same footprint as
the W8 3-way system and has been engineered to extend the Wavefront W8's
performance to below 40Hz.

Like all flown Wavefront products, the W8S is fitted with MAN load-certified flying
points and is designed to comply with the 12:1 safety factor specified by the German
VBG70 standard when used with compatible 12:1 flying flying systems. One important
advantage of the MAN flying system is that inter-cabinet connections place a minimal 
load on the cabinets and, being external, can be load certified and inspected 
independently.

A2.2 Specifications

Type: 

Hybrid™ bass system

Frequency response: 

40-150Hz +/- 3dB

Low frequency limit: 

-10dB at 30Hz

Driver: 

1 x 15" (380mm) horn loaded
1 x 18" (460mm) reflex loaded

All material © 2007. Martin Audio Ltd. Subject to change without notice.

Summary of Contents for Wavefront W8CT
























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands