![background image](http://html1.mh-extra.com/html/marta/mt-4269/mt-4269_user-manual_1732199010.webp)
10
Switch on all heating elements by selecting heating mode «All heat», set the maximum temperature to 230°C and timer for 15 minutes. Some smoke or odour may be produced at the first switch-
on, this is normal and not a malfunction. At the end of this cleaning procedure, let the unit cool down, after which it will be ready for operation.
USING THE APPLIANCE
SWITCHING ON
Connect the device to the power supply.
Install a bake tray and/or wire rack, place the food. If the food is cooked on the wire rack/rotisserie, place the bake tray on the bottom level to prevent oil/grease/juice droplets from getting onto the
heated surfaces.
Select the desired program as described below in the section "SETTING PROGRAMS AND MODES" and, if necessary, turn on the convection mode.
To start the program, press the "Start / Cancel" button (33). The device will start working.
After the set time has elapsed, a beep will sound and the device will stop working.
If you need to stop the program before it ends, you need to press the "Start / Cancel" button again.
If the products have not reached the desired degree of readiness, set the additional operating time of the device and the desired operating mode of the heating elements.
To avoid burns, do not touch hot surfaces!
In order to get better cooking performance, it is recommended to pre-heat the oven about 10-15 minutes. DO NOT USE THE APPLIANCE MORE THAN 4 HOURS WITHOUT A BREAK.
SETTING PROGRAMS AND MODES
Automatic programs "Bread / Cake","Def / Ferm"(Defrosting / Fermentation),"Cookie / Tart ","Meat / Potato" can be selected by pressing the"Menu" button (19). Note: The quality of the dishes
obtained as a result of using automatic programs depends on the products used, their weight and proper preparation.
The heating elements and the rotating mode of the rotisserie can be selected by pressing the button «Select»:
▪
Up-heat – the upper heating elements operating mode (15)
▪
Low-heat - the lower heating elements operating mode (16)
▪
All heat - all heating elements operating mode (28)
▪
Roti – rotisserie rotation mode (29)
You can change both the cooking time and the temperature in the programs. To do this, after selecting the program, press the "Time / Temp" button (20), set the desired time (up to 120
minutes) by pressing or holding the "+" or " - " buttons (21). Then press the "Time / Temp" button again and set the desired temperature. To start the program, click the "Start / Cancel"). The device
will start working. After the set time has elapsed, the device will turn off and notify you with an audible signal that the set program has been completed.
The convection mode can be switched on and off by pressing the "Conv" button (23) before the program starts. During the operation of the convection, the display shows the
indicator of the operation of the convection mode (24).
Pre-set – delayed start up to 24 hours
This function is to activate the execution of the program after the required time interval within 24 hours. To program the delayed start, turn on the appliance and, in standby mode, press the "Pre-
set" button (32), set the desired time by pressing or holding the "+" or "-" buttons before starting a programm by pressing or holding the "+" or " - " buttons, then proceed to select the preferred
program, cooking time and heating temperature. The corresponding indicator (11) and time before start will be displayed on the display.
The table below shows the available time and temperature setting ranges, as well as the default program settings.
Designations: «
+
» – heating elements are on, «
///
» - usage not available.
OFF/ON – disabled by default. Activation is available by pressing the button «Conv» (23).
ON/OFF – enabled by default. Deactivation is available by pressing the button «Conv» (23).
Function
Time Range
Default Time
Temp. Range
Default Temp.C
Upper Heat
Lower Heat
Convect.
Rotisserie