background image

14 of 16

104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127  •  Fax 800-477-6341 / 641-753-6341 www.MARSHALLTOWN.com

WS3664

HOW TO OPERATE

FUEL AND OIL

Make sure gas tank has plenty of 86 octane or higher gasoline.  
Your 4 stroke Honda engine uses straight gasoline. NEVER 
USE A GAS/OIL MIX. Empty entire bottle of provided Honda 
engine oil into crank case. The maximum oil capacity is 3.5 oz. 
Always lay screed down on roll cage as shown when filling gas 
and oil or checking oil. NEVER OVERFILL.
 

STARTING

 
1.  On a cold engine, move choke lever to CLOSED 
     position. To restart a warm engine leave choke in 
     OPEN position
 
2.  Press priming bulb repeatedly until fuel can be 
     seen in the clear-plastic fuel-return tube.
 
3.  Press On/Off Switch to the On Position. 

4.  Pull the starter grip lightly until you feel resistance,  
     then pull briskly. Repeat until engine starts.
 
5.  If the choke lever was moved to the CLOSED  
     position to start the engine, gradually move it to  
     the OPEN position as the engine warms up.
 

RESTARTING A WARM ENGINE

 
1.  Leave the choke lever in the OPEN position.  
 
2.  If there is no fuel in the clear-plastic fuel-return   
     tube, press priming bulb repeatedly 
     until fuel can be seen in the tube. 
 
3.  Press On/Off Switch to the On Position
 
4.  Pull the starter grip lightly until you feel resistance,  
     then pull briskly. Repeat until engine starts.

 

CLOSED

OPEN

1

2

3

4

Summary of Contents for SHOCKWAVE 2.0 POWER SCREED

















Reviews: