background image

OWNER’S MANUAL 

 

MODEL DH1-1010 SERIES – HEATED HOLDING UNIT

                              

174830 RV120817 
Copyright © 2017 Marshall Air Systems, Inc. 
All Rights Reserved. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
KEEP THIS MANUAL IN A SAFE PLACE AND RETAIN FOR FUTURE USE. 
 
Cabinet area must be kept free of combustible materials and the flow of ventilation air must not 
be obstructed. Operating personnel must not perform any maintenance or repair functions. 
Contact your Qualified Service Company. 

 

CLEAN UNIT AND BASE WITH A DAMP CLOTH/RAG AND A MILD CLEANER.   

DO NOT USE A GREEN SCOTCH BRITE PAD OR ANY OTHER ABRASIVE CLEANING PAD.  THE 
BLUE SCOTCH BRITE (NO SCRATCH) IS SAFE TO USE. 

DO

 

NOT

 

USE

 

CAUSTIC

 

CLEANING

 

SOLUTIONS SUCH AS OVEN CLEANER.  USE ONLY MILD, 

NON-ABRASIVE CLEANER. 

DO NOT IMMERSE IN WATER! 

 

FOR YOUR SAFETY 

 

DO NOT STORE OR USE GASOLINE OR OTHER 

 

FLAMMABLE VAPORS OR LIQUIDS IN THE 

 

VICINITY OF THIS OR ANY OTHER APPLIANCE

 

AVERTISSEMENT 

Ne pas entreposer ni utiliser de l’essence ni d’autres vapeurs ou liquides inflammables dans 
le voisinage de cet appareil, ni de tout autre appareil. 

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, OR MAINTENANCE CAN CAUSE 
PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATION AND MAINTENANCE 
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT. 

AVERTISSEMENT: Une installation, un ajustement, une altération, un service ou un entretien 
non conforme aux normes peut causer des dommages à la propriété, des blessures ou la mort. 
Lisez attentivement les directives d’installation et d’opération et d’entretien avant de faire 
l’installation ou l’entretien de cet équipement 

Summary of Contents for DH1-1010 Series

















Reviews: