background image

Select the “

Jug Filled

” option if water will be added to the brewer manually. To manually fill with 

water;

1. 

  Lift the filler lid

2.

   Fill with water to the 

 

MAX level (Ref. D)

4.

   Close the filler lid

SETTING UP YOUR BREWER

5

  JUG FILLED – MANUAL FILLING WITH WATER

Only use FILTERED cold water when refilling. Failure to do so could result in premature 

failure of the machine.

Take care not to overfill tank.

If tank runs out before water is refilled, the display will read “Please open lid and add more 

water”

If tank is overfilled water will flow out from underneath filterpack door and into drip tray.

● 

Notice  

  PRIMING THE HOT WATER SYSTEM

 (INITIAL INSTALL ONLY)

You cannot brew beverages if you have not primed the brewer first! The priming cycle fills the hot 

tanks with water and removes any air from the system. After this, your brewer will be ready for use.

 

NOTE: Unless the system is fully primed the water heaters will not be enabled.

1.

  From the Operator Menu (Ref. C) 

 press 

“Next”

 until the menu option

 

“Hot Tank Control:”

 is shown.

2.

  Select the 

“Prime”

 option (Ref. E)

HOT TANK CONTROL
Disabled (Tank Empty)

PRIME HOT WATER SYSTEM

Exit Menus

<Back

<Next

Disable>

Prime>

The brewer will now start to fill the boilers with water from the cold tank. The message at the 

bottom of the screen will change to show “

HOT TANKS FILLING

”. The filling sequence will take 

approximately 2 minutes after which the screen will change to show “

WATER HEATING

”.

  PRIMING THE HOT TANKS 

(INITIAL INSTALL ONLY)

(Ref. E)

When priming, the brewer will automatically stop the water when sufficient water has 

been pumped. If for any reason you need to stop the water pumping during the prime, 

press the “

Disable

” option. This will stop the pump. You will need to re-start the priming 

sequence again by pressing “

Prime

” when ready.

Notice  

After successfully priming the brewer, the display will change to say “Please wait while the water 

heats up”.

When the water is hot the main menu will be displayed. Your brewer is now ready to use.

(Ref. D)

Summary of Contents for FLAVIA CREATION C500





















Reviews: