MarineKinetix MK4+ User Manual Download Page 18

MK4+ Hybrid Charge Controller                                                          User Manual

 

17                                         

 

8. Guarantee and Liability 

Warranty 
 
Marinekinetix warrants your product to be free from defects in material and/or 
workmanship for a period of 3 years from original date of purchase. Warranty 
coverage is extended only to original purchaser. 
 
If product proves defective during warranty period, Marinekinetix, at its option 
will: 
1. Replace the controller with a new or refurbished product. 
2. Correct reported problem 
 
Customers warranty continues to be valid on repaired or replaced product from 
original component warranty date. 
 
Restrictions 
 
This  warranty  covers  defects  in  manufacturing  discovered  while  using  the 
product as recommended. The warranty does not apply to: 
 
Equipment, materials, or supplies not manufactured by Marinekinetix.   
Product  that  has  been  modified  or  altered  other  than  by  Marinekinetix,  or 
without prior Marinekinetix approval. 
Lightning, corrosion, or water damage 
Repairs performed by other than authorized Marinekinetix support staff 
Normal wear and tear and corrosion from exposure to the marine environment 
Acts of God; misuse, negligence, and accidents 
 
Disclaimer 
 
EXCEPT  FOR  THE  EXPRESSED  WARRANTY  SET  FORTH  ABOVE,  THE 
MANUFACTURER  DISCLAIMS  ALL  OTHER  EXPRESSED  AND  IMPLIED 
WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF FITNESS FOR 

PARTICULAR 

PURPOSE, 

MERCHANTABILITY 

AND 

NON-INFRINGEMENT.    NO  OTHER  WARRANTY,  EXPRESSED  OR 
IMPLIED,  WHETHER  OR  NOT  SIMILAR  IN  NATURE  TO  ANY  OTHER 
WARRANTY  PROVIDED  HEREIN,  SHALL EXIST WITH  RESPECT  TO  THE 
PRODUCT  SOLD  UNDER  THE  PROVISIONS  OF  THESE  TERMS  AND 
CONDITIONS.  THE  MANUFACTURER  EXPRESSLY  DISCLAIMS  ALL 
LIABILITY  FOR  BODILY  INJURIES  OR  DEATH  THAT  MAY  OCCUR, 
DIRECTLY OR INDIRECTLY, BY USE OF THE PRODUCT BY ANY PERSON. 
ALL  OTHER  WARRANTIES  ARE  EXPRESSLY  WAIVED  BY  THE 
CUSTOMER. 

Summary of Contents for MK4+




















Reviews: