96
EN
• Ensure that the straps are parallel and level. The distance between the belts
corresponds to the dimension N in the table on page 4 for the respective pool
size.
Refit the rear plates and collections
• Using a straight edge (you can use a heel plate), align the area on which the base
plate is to lie.
• Compact the surface, and then compress it again and compact it again. The surfa-
ce must be perfectly flat.
• Lift the belt [8] slightly and insert the 4 screws [21] into the holes in the belt (Fig.
3A-4).
• Attach the heel plate [11], the bowl [23] to the bolts and screw and tighten the
nuts [10] (Figures 3A-4 and 3A-5).
• Attach the column [9] to the bowl [23] and fasten both parts with bolts [21] and
nuts [10] (Fig. 3A-6).
• Make sure that a posture of approx. 2 mm (Fig. 3A-7) is left below the side edge
of the post after mounting the post.
• Tighten the screw connections firmly.
• Repeat steps a. - g for all columns.
Remove screws
• Insert the bolts into the holes in the post [9] by sliding the bolt [15]. First place
the strut in the horizontal position (Fig. 3A-8) and slide it into the post. Then
push the joint upward and lower the other end to the ground (Figures 3A-9 and
3A-10).
VERY IMPORTANT: Secure the upward pressure upward on the post joint and the
sloping struts for the entire length of time you fold the opposite end of the incli-
ned strut to the ground.
• Align an oblique strut [15] with holes in the sloping clamp [16] attached to the
end of the belt [8] in one of the holes at the lower end. With such flat holes, slide
the two long screws [26] (Figures 3A-11). Screw the nuts [10] onto the screws
and tighten the couplings, but do not strain to avoid deformation of the parts.
• Ensure that when installing inclined struts, do not release the locks in the juncti-
on of the post
[9] and inclined struts [15].
Identify lower pads
The 3,7x5,5m oval pool includes 4 13-A rails and 6 circular rails 13.
NOTE: The use of the rails follows from the picture: Type 13-A - bar for the transiti-
on part, type 13 - bar for the circular part, type 13-C - bar between struts.
Put the lower cylinder C
• Some pools are equipped with a reinforcement (Figures 3A-13). In this case, slide
the brace into the center of the C-bar (Fig. 3A-14).
• Insert a C-shaped curved bar between neighboring posts (Figures 3A-15). Place
it exactly as shown in Figure 3A-20, ie with the groove up and inward of the pool
and the top edge into the notch of the post.
Summary of Contents for Orlando Premium 10310019
