background image

Dustmaster

® 

28,000 CFM Tier 4 Diesel Dust Collectors

25

MAINTENANCE

Adjust Pulse Separation

3)  Set the Pulse Separation, the elapsed 

time between pulses, by moving Knob 

(3). The recommended elapsed time 

between pulses is the minimum time 

needed for pulse header to return to full 

pressure. Depending on conditions, the 

elapsed time may need to be changed. 

Elapsed time between pulses should be 

between 5–15 seconds.

1)  Open enclosure door of Timer Controller.

2)  Locate Adjustment Knobs (1 and 2).

4)  Set Pulse Duration, the elapsed time of 

compressed air entering the filters, by 

moving Knob (4). The recommended 

elapsed time of compressed air entering 

the filters is 200 milliseconds (mSEC). 

Depending on conditions, the elapsed time 

of air entering the filters should be between 

200–350 milliseconds.

5)  Close enclosure door of Timer Controller.

1
2

3

4

Always depressurize 

the entire system, 

disconnect all power 

sources and lockout/

tagout all components 

before any maintenance 

or troubleshooting is 

attempted. Failure to 

comply with the above 

warning could cause 

electrical shock and 

inadvertent activation of 

equipment resulting in 

death or serious injury.

W-562

Summary of Contents for DUSTMASTER





































Reviews: