manualshive.com logo in svg

Marantz RX-77, User Manual

Share
Download
Marantz RX-77 User Manual Download Page 6

User Guide

6

Hardware 

Red LED (continuously on when powered, blinking during RF reception)
16 IDs and 4 CHs , 4 outputs for IR emitters

 

Dimensions 

4.5 x 3.2 x 1.2 inch (113 x 81 x 30 mm)  

Operating 

32°F to 122°F (0°C to 50°C) 

temperature  

Infrared (IR) 

Operating distance: up to 16 feet (5 meters)

IR frequency range: DC/flash codes, 36kHz-550kHz  

Radio 

Operating distance: up to 100 feet (30 meters)

frequency (RF)  

depending on the surrounding conditions
Frequency: 418 MHz (US) , 434MHz (Europe) 

Dual IR emitters 

Number of IR emitters: up to 8 (4x2), emitters wired in series
3.5mm mono mini-plug
Cable length: 10 feet (2.5 meters) , Max. range: 3 feet (75 cm)

Accessories AC Power adapter (400mA/12V DC adapter)

Mounting kit (Plate and 4 screws)  

Approvals 

The device complies with part 15.19(a)(3) of the FCC Rules.
Operation is subject to the following two conditions: (1) this device 
may not cause harmful interference and (2) this device must accept
any interference received including interference that may cause 
undesired operation.

 

Specifications

RX-77  07-25-2001  Page 6 of 6

IR emitter x 4

The specification and design of this product are subject to change without notice.

Summary of Contents for RX-77







Reviews:

No comments

Brands by name

Popular brands

Load more brands