ENGLISH
8
LEARN MODE
This remote controller is capable of learning and
storing codes used by other remote controls that you
already own.
For codes which are not learned, the remote
controller will transmit either the Marantz preset
codes from the initial settings, or remote codes from
another manufacturer’s AV equipment which is set
by the customer.
The receiver sensor for the remote control signals is
located at the top of the remote controller.
Notes:
• This remote controller is capable to learn around 60
codes.
• When the batteries are getting weak , the learing
procedure is not successful.
LEARNING PROCEDURE
1.
Place the remote controller so that its infrared
signal transmitter is facing the infrared signal
receiver on the Marantz remote controller at a
distance of about 2 inches (0.05 m).
SYS
TEM
R
EMO
TE C
ONT
ROL
LE
R
2 inches
2.
Press and hold down the
SET
and
MENU/
INPUT
buttons until LEARN indicator blinks.
3.
Select
the
SOURCE
button to select the
SOURCE.
4.
Select the button to be learned.
• LEARN indicator lights up.
When the following key learned
•
SOURCE
buttons
The learning function is unavailable for all
SOURCE buttons in any mode.
•
POWER ON
button
•
POWER OFF
button
•
VOL +/-
button
•
MUTE
button
•
INFO
button
•
SLEEP
button
The above keys are common use in each
device mode. It can be learned in TV mode.
5.
Press and hold the button of the original remote
controller to learn until the SEND indicator
blinks twice.
• When the SEND indicator blinks once,
repeat this step.
• When the memory of the RC101 is full, the
LEARN and SEND indicators blink once.
If you want to learn the code, you should
erase other learned button.
6.
Repeat
steps
4
and
5
to learn other buttons in
same SOURCE.
7.
Repeat
steps
3
to
6
to learn other SOURCE.
8.
When you have finished programming the
remote controller, press the
SET
button, then
LEARN indicator stops blinking and exits from
the LEARN mode.
Notes:
• When the SEND indicator blinks once again, the
transmitting code is unavailable for RC101, or the
transmitting signal is intercepted by noise.
• If no buttons are pressed for approximately 1
minutes while in the LEARN mode, the remote
controller automatically exits from the LEARN
mode.
ERASING PROGRAMMED CODES (RETURNING TO
INITIAL SETTINGS)
Codes can be erased in three ways: by buttons,
sources, and by all memory contents.
Erasing the code by buttons
1.
Press and hold down the
SET
and
MENU/
INPUT
buttons until LEARN indicator blinks.
2.
Select
the
SOURCE
button to select the button
to be erased.
3.
Press and hold down the
SLEEP
button and
press the learned button twice to be erased.
• SEND indicator blinks twice and the mode
returns to LEARN mode.
4.
To return the NORMAL mode, press the
SET
button.
Erasing the code by SOURCE
1.
Press and hold down the
SET
and
MENU/
INPUT
buttons until LEARN indicator blinks.
2.
Press and hold down the
SLEEP
button and
press the learned
SOURCE
button twice to be
erased.
• LEARN indicator lights.
3.
Press
ENTER
button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press
ENTER
button and simply touch any
other button.
4.
To return the NORMAL mode, press the
SET
button.
Erasing the all SOURCES
1.
Press and hold down the
SET
and
MENU/
INPUT
buttons until LEARN indicator blinks.
2.
Press and hold down the
SLEEP
button and
press
POWER ON
and
POWER OFF
button.
• LEARN indicator lights.
3.
Press
ENTER
button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press
ENTER
button and simply touch any
other button.
4.
To return the NORMAL mode, press the
SET
button.
Note:
Erasing codes will return to the factory preset code,
or there will leave empty if the button has no factory
preset code.
